SHENZHEN XINWU TECHNOLOGY XW-133-D9 Intelligent Visual Door Bell User Manual

SHENZHEN XINWU TECHNOLOGY XW-133-D9 Intelligent Visual Door Bell

Product instruction

• Doorbell:
  

• DingDong:
  

Product functions

visualizable talking:

when someone press the doorbell， cellphone that combined to it will receive a notification, and will be able to talk to visitor.

share doorbell:

you can shall your visitor records to other users. other user needs to download app and log in. (supports maximum 9 shares, only 1 can answer the doorbell.)

low power warning：

cellphone will receive a notification when device is low power. please change the 4*AA battery in time.

How to use

1. scan the QR code below and select proper system(iOS/android) to download app
   (X Smart Home)
   App Store (IOS)
   Google Play (Android)
   

2. Register and log in : you can register an account with email address or you can log in by guest account. Guest account is able to use all functions of the app, but device will delete all guest info after device is reset.

3. click “+” button on upper right corner, follow app instructions to add device and combine with your cellphone.

4. Binding device : this Doorbell doesn’t support 5G Wi-Fi channel ! Be sure to select the 2.4G Wi-Fi channel and start binding device. 5G Wi-Fi of dual channel router usually has “-5g” mark after the name. Remember NOT to select this Wi-Fi for device binding.
   For example： “NAXCLOW_2.4G” Correct channel
   “NAXCLOW_5G” Wrong channel

if you have modified the wifi channel name, make sure you choose the correct channel for binding.

if you are not sure about the wifi channel, you can login your router backstage for more info. (sticker on the back of router housing)

(type router ip address in we browser, open the link and input user name and password.

5. Working logic of doorbell push: press the doorbell after binding, the app will receive the message push, select “reject” or hang up after answering, the doorbell will enter the shutdown state, which can trigger the doorbell to send messages to the mobile phone again.

If we don’t do any processing on the messages, we will only push one message to the mobile phone within 30 seconds to avoid the excessive interference of junk messages caused by others’ malicious doorbell ringing. New messages will not be pushed to you until the device is shut down after 30 seconds and the doorbell is triggered again.

Warnings :

• please turn on Bluetooth, Wi Fi and allow all permissions of the app.
• please use this product in an environment with good Wi Fi signal and try not to stick it on the metal door.
• this product does not support 5g Wifi.
• before installing the doorbell, please conduct normal function test at the position to be installed to ensure that the product works properly. Remove the lens protective film after installation.

Pair Doorbell & Dingdong

1. Plug Dingdong in power souce.
2. Long press Dingdong match button for 2 seconds, indicator light on suggesting enters pairing mode.
3. Press doorbell button once, 2 devices will pair with each other, after paired successfully, indicator lights off.

Warnings:

1. During pairing, 2 devices should be as close as possible.
2. Make sure the doorbell is fully charged.
3. After pairing, the indicator light will automatically turn off.
4. If you don’t ring the doorbell within ten seconds, the dingdong indicator will go out automatically.
5. If pairing fails or re pairing is required, please repeat the pairing process.

Reset & Restore factory settings

Reset: press and hold the doorbell key for ten seconds until the doorbell sounds “reset succeeded”.

Restore factory settings: in case of equipment crash or other factors, remove the doorbell and press the black button in the doorbell reset pin hole.

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>