SAL STS600BTAM PIXIE Smart Timer Switch G3 User Guide
- June 8, 2024
- SAL
Table of Contents
STS600BTAM PIXIE Smart Timer Switch G3
User Guide
Foreword
IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ
THESE GUIDE AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
standard terms and conditions of sale, available via
www.sal.net.au.
Due to continued product and information updates, product data sourced from
sal.net.au shall not form part of any contract and or technical performance
guarantee
unless expressly confirmed in writing by SAL at the time of order.The product
wireframe drawings in this document are intended for illustration purposes
only and may differ
from the final physical product. The installation instruction is subject to
change without prior notice.
Product Introduction
PIXIE Smart Switch G3 is the third generation smart time delay switch, that
permits the supply of electricity to the load for a predetermined time
duration after being triggered.
2.1 Product Features
- Fits most branded switch plates
- Fits 1 to 6 gang wall plate installation
- Over temperature protection, overload protection, short circuit protection
- Automatically turns off after a predetermined time duration
- Time duration can be programmed manually and via the App. When programming manually, only hourly timer functions can be set, the period is from 1 hour to 24 hours. When programming via the App, the time duration can be set from 1 minute to 24 hours
- Manual override function available
- Multiway control – When pairing multiple PIXIE multifunction control device (e.g. SMF/BTAS) with the same smart Timer Switch, multiway timer control is achieved
- LED indicator can be enabled and disabled in the App
- In the last 1 minute of timer mode, the LED indicator flashes quickly indicating imminent time out
2.2 The package includes
- PIXIE Smart Timer Switch G3 * 1
- Extra key caps * 2
- Silicon spacer * 1
- Load correction capacitor * 1
- Quick Start Guide * 1
**2.3 Product illustration***
*All drawings shown are for illustration purpose only, actual product may vary due to product enhancement.
Specifications
3.1 Basic specifications
Model No.| Input (V)/(Hz)| Min / Max loads| Colour| Dimension L x W x H (mm)|
Wireless
---|---|---|---|---|---
STS600BTAM| 240/50| 9*/600W| Blue| 42 x 24 x 24| Bluetooth Mesh Technology
3.2 Load rating
No. of switch| Resistive load (Incandescent/High voltage halogen
lamp)| Capacitive load (e.g. LED, CFL)| Inductive load (e.g.
exhaust fan)
---|---|---|---
1| 600W| 400VA| 120VA
2| 500W| 250VA| 100VA
3| 500W| 200VA| 80VA
4| 300W| 150VA| 80VA
5| 300W| 150VA| 60VA
6| 200W| 100VA| 60VA
3.3 Load compatibility
Compatible Loads| |
---|---|---
| Incandescent lamp| Yes
| 240V halogen lamp| Yes
| Low voltage halogen with electronic transformer| Yes
| CFL| Yes
| LED fixture| Yes
Wiring and Installation
STS600BTAM – Standard wiring diagram
STS600BTAM – Optional wiring diagram
The complimentary capacitor given in the carton operates as a load correction device to assist improving compatibility performances.
Installation process
- Make sure the key cap compatibility (pry and replace the default key cap if necessary)
- Check and confirm the load compatibility
- Turn OFF the mains electricity supply before commencing installation
- Connect the switch according to the wiring diagram
- Turn ON the mains electricity supply, wait for 10 seconds, then test the switch operation by pressing the switch button.
Operation
The smart timer switch can work under two modes,
Timer Mode: The switch is expected to automatically disconnect the
electricity to the load after being turned on for a predetermined time
duration.
Manual override mode: The swtich supplies electricity permanently until
further operation to switch off or exit this mode Manual setting time duration
(optional, programming in the App is more recommended)
- Turn off the switch
- Push and hold the button for 10 seconds, the LED indicator will start to slowly cycle indicating the programming mode has launched
- To program, press the button between 1 and 24 times according to the desired delay in hours. E.g, 8 presses will result in a delay of 8 hours. Pressing more than 24 times will result in a time duration of 24 hours. Programming mode expires 10 seconds after the last button press. At this time the new timer duration is saved.
(Note: If no button press is detected in programming mode, the time duration will be unchanged.)
Manual setting time pairing (optional, for multi-way time delay control)
- Turn off the switch
- Quickly press the button of STS600BTAM 4 times, make sure the LED indicator is flashing in blue and white
- Quickly press the button of SMF/BTAS or SMRM/BTAS 4 times within 30s. When their LED indicator flashe twice and then remain lit for 2s, the pairing is successful.
Note: If the STS600BTAM changes HOME setup in the App or reset to factory, the pairing process will need to be repeated.
When in off state
| Operation | Function Description | LED Indicator |
|---|---|---|
| 1 Click | Turn on the switch and start timer mode | Quickly flash for 5s then |
flash every 3s
4 Clicks| Enter pairing mode, this mode stays 30s| Quickly flash in blue and
white for 30s
Long press for 2 seconds then release| Turn on the switch in an untimed manner
(manual override mode)| Static high brightness
9 Click| Reset all the settings to factory| Flash in blue and white 3s then
stay lit for 2s
When in timer mode
| Operation | Function Description | LED Indicator |
|---|---|---|
| 1 Click | Turn off the switch and cancel timer | Static low brightness |
| 2 Clicks | Keep switch on, timer will count again | Quickly flash for 5s then |
flash every 3s
Long press for 2 seconds then release| Enter manual override mode, the switch
stays on in an untimed manner| Static high brightness
When in manual override mode
| Operation | Function Description | LED Indicator |
|---|---|---|
| 1 Click | Exit manual override mode, start timer | Quickly flash for 5s then |
flash every 3s
Long press for 2 seconds then release| Turn off the switch, exit manual
override
mode| Static low brightness
How to download App
Scan QR code or go to App store (IOS) or Google Play (Android) to download the free PIXIE app to your smart phone.
- IOS: Requires IOS 6.0 or later. Compatible with iPhone, iPad and iPad touch
- Android: Requires Android 4.4 or above, devices must support Bluetooth 4.0 Specifications above are for reference only and may vary without prior notice.
|
---|---
https://www.pixie.app/download/pixie/|
https://www.pixie.app/download/pixieplus/
Warranty
In accordance with SAL’s standard terms and conditions of sale, SAL warrant
this product to be free from defects in materials and or workmanship for a
period as stated below for goods not subject to incorrect installation,
maintenance, operation, mishandling, environmental, unauthorised modifications
or electrical operating conditions outside the nominated product specification
as detailed in these installation instructions. The benefits to you given by
this warranty are in addition to other rights and remedies you have under law.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.
Warranty term – Residential usage (12) months, Commercial usage (12)
months
7.1 How to make a claim?
Step #1 – Within 30 days of the fault discovery, please contact the
original place of the SAL product purchase during standard (local) business
hours, with the following information (a) proof of purchase (b) description
and quantity of the claimed fault (c) address of installation. (d) operating
hours of the product.
Step #2 – It is then the responsibility of the original place of product
purchase to report the matter to SAL aftersales;
NSW | ACT| SAL National Pty Ltd, 40 Biloela Street Villawood NSW 2163| | P #
02 9723 3099
---|---|---
QLD| SAL National Pty Ltd, 36 Whitelaw Place Richlands QLD 4077| | P # 07 3879
5999
VICT | TAS | SA | NT| SAL National Pty Ltd, 46-48 Keys Road Moorabbin Victoria
3189| | P # 03 9532 3168
WA| SAL National Pty Ltd, 29 Beringarra Av Malaga WA 6090| | P # 08 9248 7458
Step #3 – Upon review of your claim and if the product is required to be
returned to SAL for technical evaluation, then at the owners expense the
product must be returned to SAL as per the above nominated locations.
Step #4 – Pending the evaluation, the claim will be validated resulting
in the product being repaired or replaced with the same or best equivalent
product at the discretion of SAL, or rejected if the product fault was found
to be caused by conditions beyond the responsibility of SAL warranty
obligations. Consideration of installation, product removal, return freight
and or testing fees are not the responsibility of SAL.
Scan QR code to get full installation instruction
https://pixie.app/product/FLBP24VCCTBTAM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>