SKYDANCE S1-B+R11 AC Triac RF plus Push Dimmer Kit Owner’s Manual
- June 8, 2024
- SKYDANCE
Table of Contents
AC Triac RF + Push Dimmer Kit
Model No.: S1-B+R11
RF dimming/Leading edge or trailing edge/Min brightness settable/Push Dim/Wall junction box mounting
Features
- RF + Push AC phase-cut dimmer, 1 channel output.
- To dim and switch single color dimmable LED lamps, traditional incandescent and halogen lights.
- Leading edge dimming or trailing edge dimming set by dip switch.
- Min brightness can be set by key.
- Light on/off fade time 3s selectable.
- Connect with external push switch to achieve on/off and dimming function.
- Easy to be inserted into standard 86*86mm wall box.
Technical Parameters
Triac Dimmer’s Input and Output
Input voltage| AC100-240V
Output voltage| AC100-240V
Output current| Max 1.5A
Output power | 150-360W
Dimming signal | RF 2.4GHz + Push Dim
Dimming level| 256 levels
Dimming range| 0 -100%
LED Remote’s Input and Output
Output signal | RF(2.4GHz)
Working voltage| 3VDC(CR2032)
Working current| ＜5mA
Standby current| ＜10μA
Standby time| ＜1 years
RF Control distance| 30m(Barrier-free space)
Safety and EMC
EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4
Safety standard(LVD) | EN 62368-1:2020+A11:2020
Radio Equipment(RED)| ETSI EN 300 328 V2.2.2
Certication| CE,EMC,LVD,RED
Environment
Operation temperature| Ta: -30ºC ~ +55ºC
Mechanical Structures and Installations
- AC Push switch
- Match / Min brightness set key
- DIP switch for Leading edge or trailing edge phase-cut select
- AC N output
- AC L output
- AC L input
- AC N input
Typical Wall Junction Box Mounting
Remote function
- LED indicator
- On/Off
- 100%
- Bright touch slide
- 50%
- 1%
- Back holder with magnet
Compatible Load Types
| Load Type | Maximum Load | Remarks |
|---|---|---|
| Dimmable LED lamps | 200W @ 220V 100W @ 110V | Due to variety of LED lamp |
designs, maximum number of LED lamps is further dependent on power factor
result when connected to dimmer.
Triac Dimmable LED drivers| 200W @ 220V 100W @ 110V| Maximum permitted number
of drivers is 200W divided by driver nameplate power rating, and make sure the
surge current is no more than 2 times 65A.
Incandescent lighting, HV Halogen lamps| 400W @ 220V 200W @ 110V|
Wiring diagram
Caution: Please carefully ensure all wire connections and polarities are correct and secure before applying power, otherwise this dimmer will be damaged.
- Push Switch
- Dimmable LED light
Connect with dimmable LED light
- Push Switch
- Triac Dimmable
- LED Driver
- LED light
Connect with Triac dimmable LED driver
Note: When calculating the maximum number of load lamps or drivers, the input
power or input current parameters of a single lamp or driver must be used, the
output power parameters can not be used.
In addition, the maximum surge current of the dimmer is 65A, the sum of surge
current of multiple dimmable LED drivers should not exceed 2 times. otherwise,
the product will be overloaded and damaged.
Leading edge or trailing edge dimming setting
Select leading edge(forward-phase) dimmer or trailing edge(reverse-phase) dimmer according to dimmable LED light or driver.
Reverse-phase
Forward-phase
Caution: before power on, you must confirm the selection of dip switch.
Min brightness setting
Long press Min set key for 2s, the light blink 2 times, ready for min
brightness set, then short press Min set key 1-6 times, to get 6 min
brightness: 5%, 10%, 15%, 20%, 25% or 30%, the light will output the current
min brightness immediately, Long press Min set key for 2s or wait 8s, quit min
brightness set, the light will output 100% brightness automatically.
Light on/off fade time
Long press Match key 5s, then short press Match key 3 times, the light on/off
time will be set to 3s, the indicator light blink 3 times. Light on/off fade
time Long press Match key 10s, restore factory default parameter, the light
on/off time also restore to 0.5s.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered
for selection:
| Use the controller’s Match key | Use Power Restart |
|---|
Match:
Short press Match key, immediately press on/off key of the remote. | Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Press and hold Match key for 5s to delete all match,
The light blinks 5 times means all matched remotes were deleted.| Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
User Manual Ver 1.0.0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>