Fanvil i61 Outdoor Audio and Video Doorphone Installation Guide
- June 5, 2024
- Fanvil
Table of Contents
i61 &i62&i63&i64
Quick Installation Guide
www.fanvil.com
Package Contents
| Video Door Phone
---|---
| Quick Installation Guide
| RFID Cards 2pcs
| Connector
| Mounting Template
| Screw and tool
Physical specification
| Model | Device sizeevice |
|---|---|
| i61 | 159.7 x 88 x 36.15 (mm) |
| i62&i63&i64 | 177.4 x 88 x 36.15 (mm) |
1) Panel
2) Interface description
Open the rear case of the device, there is a row of terminal blocks for
connecting the power supply, electric lock control, etc. The connection is as
follows：
| Serial number | Description |
|---|---|
| 1 | Ethernet interface: standard RJ45 interface, 10/100M adaptive, |
it is recommended to use five or five types of network cable
2| Two sets of short-circuit input detection interfaces: for connecting
switches, infrared probes, door magnets, vibration sensors, and other input
devices
3| Wiegand interface
4| RS485 interface
5| Power interface: 12V/1A input up positive, down grounded
6-7| Two sets of short-circuit output control interfaces:
used to control electric locks, alarms, etc.
8| Line out interface
3) Wiring instructions:
NO： Normally Open Contact；
COM: Common Contact；
NC： Normally Close Contact.
Driving Mode
|
Electric-lock Mode
|
Connections
---|---|---
Passive
|
No electricity when open
|
Electrify when open
√
|
√
| |
√
| |
√
|
√
|
√
| |
Installation Diagram
Panel Main Body Back Shell Wall Bracket
Figure 3-1 Three Major Parts of i61
Wall mounting
Step 1: Installation preparation
A. Check the following contents
- KM3*6 screws x3
- TA4*30mm screws x5
- φ6*30mm screw anchors x5
- PM4*16mm screw x3
- TM6#*20/ screw x3
B. Tools that may be required:
- Phillips screwdriver， hammer, RJ45 crimper
- Electric impact drill with an 8mm drill bit
Step 2: Drilling
Figure 3-2 Wall Mounting / Built-in
A. Place the mounting template with dimensions on the surface of a wall
in a desired flat position.
B. Use an electric drill to drill the 4 holes marked on the mounting
template. It is recommended to drill about 50mm deep. Remove the template when
finishing drilling.
C. Push or hammer screw anchors into the drilled holes.
Step 3: Removing hanging bracket and back shell
A. Detach the wall bracket downward from the device and loosen the four
screws on the rear cover using a screwdriver, as shown in Figure 3-3-a
3-3-b.
Step 4: Install the wall bracket, wiring, and casing
A. Align the screw holes of the wall bracket with the holes in the wall
and fix them
B. Pass all the wires through the silicone plug in the middle of the
bottom case.
All lines should be reserved for 15~20CM length, as shown in Figures 3-5.
Note: The outlet hole of the bottom case faces down.
C. Connect the cables of RJ45, power, and electric
lock to the motherboard socket as mentioned in the connector’s description
(refer to Section 2).
D. Connect the terminal of the wired cable to the motherboard socket (refer to
Section 2).
E. Test whether there is electricity by doing the following: Press the #
button for 3 seconds to get the IP address of the intercom by voice. Input the
access password or press the indoor switch to check the electric-lock
installation.
Note: Do not proceed to mount until you have finished the electric
checking.
F. Attach the device to the wall bracket in a top-down manner, locking
the screws at the bottom, as shown in Figures 3-6.
Figure 3-6
Flush mounting
Step 1: Installation preparation
A. Check the following contents:
- PM3*3mm screws x5
- PM3*4mm screws x5
- φ6*30mm screws anchors x5
- KB3*10mm screws x3
- TA4*30mm screws x5
| Appearance | Installation Diagram |
|---|---|
| 
Searching Door Phone
Here are two methods as shown below to search the device.
Method 1:
Open the door phone Network Scanner. Press the Refresh button to search the
device and find the IP address. ( Download
address：http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe
)
Method 2:
Long press the DSS key for 3 seconds(after power-on for 30 seconds), and when
the speaker beeps rapidly, Press the speed-dial button within 5 seconds, and
the system will automatically announce the IP address by voice.
In addition, the device provides the device surface DSS key operation to
switch IP address acquisition mode:
Touch and hold the speed-dial button for 3 seconds, wait for the speaker to
beep, press the speed-dial button three times within 5 seconds, and the system
will automatically announce the IP address by voice after successfully
switching to the network mode.
IP Door Phone Setting
Step 1: Log in the door phone
Input the IP address (e.g. http://192.168.1.128) into the address bar of the
PC’s web browser.
The default user name and password are both admins. 
Step 2: Add the SIP account.
Set SIP server address, port, user name, password, and SIP user with assigned
SIP account parameters.
Select “Activate”, and then click Apply to save this setting.
Step 3: Setting the DSS key
Set the DSS key as shown below for a quick start. Click “Apply” to save this
setting.
Type: Memory Key.
Number 1 : The DSS Key will dial to this Number 1.
Number 2: If Number 1 is unavailable, it will be forwarded to Number 2.
Line: Working line.
Subtype: Speed dial.
Step 4: Door Phone Setting
Door Unlocking Setting
RFID Card
- Step 1: Access control settings on a web page—>EGS Setting—Add Card Rule —>Select ” Type” (“Normal” card provides door opening function, “Add “card and “Del” card provides add and delete card function, Default “Normal” card)
- Step 2: Entere your name and card number (just enter the first 10 digits of the card number), and click “Add” to add the card to the list.
- Step3: Access the card reading area of the device through the configured ID card to open the door.
Remote Password
- Step 1: Set access control on the web page—) EGS Setting—Password— Add password rule —+ Select “Remote “
- Step 2: Enter the Name, Password, and Number, Press Add to Password Table.
- Step 3: The owner answers the access control call and presses “* ” (default password) or “123456” (new password) to open the door for visitors..
Local Password
- Step 1: Configure access on Web—EGS Setting —>Password —> Add password rule —> Select “Local ” (only the i64 supports local password access)
- Step 2: Enter the Name and Password, Press Add to Password Table.
Step 3: Owners and visitors can open the door by entering “6789” (default
password) or “123456” (new password) by using the
keypad.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>