SKYDANCE DL 4 Channels 0/1-10V DMX512 Decoder User Manual

SKYDANCE DL 4 Channels 0/1-10V DMX512 Decoder

Features

• Comply with the DMX512 standard protocols.
• Digital numueric dispaly, set DMX decode start address by buttons.
• RDM function can realize intercommunication between DMX master and decoder. For example, DMX decoder address can be set by DMX master console.
• 1/2/4 DMX channel output selectable.
• 0-10V or 1-10V output selectable.
• Logarithmic or linear dimming curve selectable.
• Stand-alone RGB/RGBW mode and 4 channel dimmer mode selectable, which be controlled by buttons with built-in programs, instead of DMX signal.
• Available in white or black.

Technical Parameters

Input and Output

Input voltage| 12-24VDC
Input signal| DMX512
Output signal| 0/1-10V analog
Output current| 4CH,20mA/CH
Safety and EMC

EMC standard (EMC)| ETSI EN 301 489-1 V2.2.3

ETSI EN 301 489-17 V3.2.4

Safety standard(LVD)| EN 62368-1:2020+A11:2020
Certification| CE,EMC,LVD
Environment

Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| T c: +65OC
IP rating| IP20
Warranty and Protection

Warranty| 5 years
Protection| Reverse Polarity
Weight

Net weight| 0.102kg
Gross weight| 0.132kg

Mechanical Structures and Installations

Wiring Diagram

Note: We recommend the number of LED drivers connected to each 0/1-10V output does not exceed 50 pieces, The maximum length of the wires from decoder to LED driver should be no more than 50 meters.

Operation

System parameter setting

• Long press M and ◀ key for 2s, prepare for setup system parameter:
  decode mode, 0/1-10V output, output brightness curve, default output level, automatic blank screen. short press M key to switch ve item.

• Decode mode: short press ◀ or ▶ key to switch one-channel decode(“d-1”), two-channel decode(“d-2”) or four-channel decode(“d-4”).When set as 1 channel decode, the decoder occupy only 1 DMX address, and four channel output the same brightness of this DMX address.

• 0/1-10V output: short press ◀ or ▶ key to switch 0-10V(“0-0”) or 1-10V(“1-0”).

• Output brightness curve: short press ◀ or ▶ key to switch linear curve(“C-L”) or logarithmic curve(“C-E”).

• Default output level: press ◀ or ▶ key to change default 0-100% level (“d00” to “dFF” ) when no DMX input signal.

• Automatic  blank screen: short press ◀ or ▶ key to switch enable (“bon”) or disable(“boF”) automatic blank screen.

• Long press M key for 2s or timeout 10s, quit system parameter setting.

DMX mode

• ● Short press M key, when display 001~512, enter DMX mode.
• Press ◀ or ▶ key to change DMX decode address(001~512), long press for fast adjustment.
• If there is a DMX signal input, will enter DMX mode automatically.
• DMX Dimming: Each DL DMX decoder occupy 4 DMX address when connecting the DMX console.
  For example, the defaulted start address is 1, their corresponding relationship in the form:
  DMX mode (001~512)

  ---

  ---

Stand-alone RGB/RGBW mode

• Short press M key, when display P01~P24, enter stand-alone RGB/RGBW mode.

• Press ◀ or ▶ key to change dynamic mode number(P01~P24).

• Each mode can adjust speed and brightness. Long press M key for 2s, prepare for setup mode speed, brightness, W channel brightness.
  Short press M key to switch three item.
  Stand-alone RGB/RGBW mode (P01~P24)
  
  Press ◀ or ▶ key to setup value of each item. Mode speed:1-10 level speed(S-1, S-9, S-F). Mode brightness:1-10 level brightness(b-1, b-9, b-F). W channel brightness: 0-255 level brightness(400-4FF). Long press M key for 2s, or timeout 10s, quit setting.

• Enter stand-alone RGB/RGBW mode only when DMX signal is disconnected or lost.
  Speed (8 level)
  
  **Brightness (10 level,100％)

**

RGB change mode list

No.

| Name| No.| Name| No.| Name
---|---|---|---|---|---
P01| Static red| P09| 7 color jump| P17|

Blue purple smooth

P02

| Static green| P10| Red fade in and out| P18|

Blue white smooth

P03

| Static blue| P11| Green fade in and out| P19| RGB+W smooth
P04| Static yellow| P12| Blue fade in and out| P20|

RGBW smooth

P05

| Static cyan| P13| White fade in and out| P21| RGBY smooth
P06| Static purple| P14| RGBW fade in and out| P22|

Yellow cyan purple smooth

P07

| Static white| P15| Red yellow smooth| P23|

RGB smooth

P08

| RGB jump| P16| Green cyan smooth| P24|

6 color smooth

Stand-alone dimmer mode

• Short press M key, when display L-1~L-8, enter stand-alone dimmer

• Press ◀ or ▶ key to change dimmer mode number(L-1~L-8).

• Each dimmer mode can adjust each channel brightness Long press M key for 2s, prepare for setup four channel brightness.
  Short press M key to switch four channel(100~1FF, 200~2FF, 300~3FF, 400~4FF). Press ◀ or ▶ key to setup brightness value of each channel.
  Long press M key for 2s, or timeout 10s, quit setting.

• Enter stand-alone dimmer mode only when DMX signal is disconnected or lost.
  Stand-alone dimmer mode (L-1~L-8)
  

Restore factory default parameter

• Long press ◀ and ▶ key for 2s, restore factory default parameter, display” RES”.
• Factory default parameter: DMX decode mode, DMX decode start address is 1, four channel decode, 0-10V output, linear brightness curve, output 100% level when no DMX input, RGB mode number is 1, dimmer mode number is 1, disable automatic blank screen.

Dimming curve setting

Malfunctions analysis & troubleshooting

1. No power.
2. Wrong connection or insecure.

|

1. Check the power
2. Check the connection.

Wrong color|

1. Wrong connection of 0-10V output wires
2. DMX decode address error.

|

1. Reconnect 0-10V output wires.
2. Set corrrect decode address.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>