LNC BRRNMJLWS4909D8 Vine 3-Light 13-in Matte Black LED Flush Mount Light Instruction Manual

LNC BRRNMJLWS4909D8 Vine 3-Light 13-in Matte Black LED Flush Mount Light

Instruction Manual

Item Number: A04909

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   » Place the wall switch in the “OFF” position.

4.  Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5.  Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8.  When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED Before starting assembly and installation please prepare the needed
(NOT INCLUDED): tools as below picture

PARTS TYPE & QTY INCLUDING:

(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Socket (3)
(G) Knob nut (2)
(H) Tube (1)
(I) Glass shade (1)
(J) Plastic washer (1)
(K) Iron washer (1)
(L) Hex nut (2)
(M) Flat cover (1)
(N) Flat nut (1)

ACCESSORIES & QTY ENCLOSED:

(A) Plastic wire connector (3)
(B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. ● Unscrew knob nuts (G) from mounting plate (C).
   ● Set them aside for later installation.
   

3. ● Pass the fixture wires through tube (H) and canopy (E).
   ● Screw tube (H) onto canopy (E) as shown in the illustration.

4. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   3 » » Go to the main fuse, or circuit breaker, box in your home.Place the main power switch in the “OFF” position.
   » Place the wall switch in the “OFF” position.

5. ●  Carefully pass the supply wires through mounting plate (C).
   ● Secure mounting plate (C) to the outlet box with mounting screws (B).
   
   NOTE: the side of mounting plate (C) marked “GND” must face out.

6. Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER
   WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES
   
   • Twist wires together with plastic wire connectors until tightly joined.
   • Wrap each connector with approved electrical tape.
   • Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box

7. ● Raise canopy (E) over the outlet box.
   ● Align canopy (E) with the pre-assembled mounting screws.
   ● Secure canopy (E) with the previously removed knob nuts (G) till snug.
   
   Note: canopy (E) should be snug against the ceiling and knob nuts (G).
   If not, adjust the threaded length on mounting plate assembly (C):
   • Unscrew the pre-assembled hex nuts.
   • Screw the pre-assembled screws in or out of mounting plate (C).
   • When the secure length is achieved, tighten the hex nuts and back to step 7.

8. »ORDERING PARTS
   Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
   CLEANING
   To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

1. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
2. Carefully let tube (H) pass through glass shade (I), plastic washer (J) and iron washer (K).
3. Tighten hex nut (L) onto tube (H) to secure glass shade
4. Carefully let tube (H) pass through flat cover (M).
5. Tighten flat nut (N) onto tube (H) to secure flat cover (M)
   
   Note: glass shade (I) should be snug against canopy (E) and flat cover (M).
   If not, adjust the threaded length in tube (H):
   • Remove glass shade (I), plastic washer (J), iron washer (K) and hex nut (L).
   • Screw the threaded pipe in or out of tube (H), then tighten another hex nut (L) as shown in the illustration.
   • When the secure length is achieved, return to step 2)

9. . Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use
exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring
pads or powders, steel wool or abrasive paper.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>