LNC A0518901 Contemporary Textured Glass Geometric LED Mini Hanging Kitchen Island Light Instruction Manual

LNC A0518901 Contemporary Textured Glass Geometric LED Mini Hanging

Kitchen Island Light

Product Information

Specifications:

• Item Number: A0518901
• Voltage: 120V
• Maximum Wattage: LED, 12W

Product Usage Instructions

Mounting Instructions:

1. Ensure the mounting surface is clean, dry, flat, and strong enough.
2. The mounting surface should be 1/4 larger than the canopy on all sides.
3. Correct any gaps between the mounting surface and canopy exceeding 3/16 as required.
4. Verify that the ceiling or wall can support the weight of the lamp.

Safety Instructions:

1. Installation by a licensed electrician is recommended.
2. Read the instructions carefully and keep them for future reference.
3. Always shut off the electricity before starting any work.
4. Avoid placing the lamp near acidic or alkaline substances.
5. When replacing bulbs, ensure the lamp is turned off and cool.

Tools Required:

• Ladder
• Philips Head or Flat Blade Screwdriver
• Electrical Tape
• Pliers
• Wire Cutter/Stripper

Parts Included:

• Mounting plate (1)
• Green ground screw (1)
• Canopy screw (2)
• Canopy (1)
• Lock nut (1)
• Cord (1)
• Pipe (1)
• Lampshade (1)
• Connector (1)
• Decorative ball (1)

Assembly & Installation Instructions:

1. Remove the fixture from the carton and check all parts and accessories.
2. Turn off the power before starting installation.
3. Screw the decorative ball to the connector as shown in the illustration.

Wiring Instructions:

Connect wires according to the provided charts. Never connect other wires to ground wires.

Frequently Asked Questions (FAQ):

• Q: Can I use a higher-wattage bulb than specified?
  A: It is recommended to use a maximum wattage of LED, 12W as stated in the specifications for safety reasons.

• Q: What should I do if the mounting surface is not clean or strong enough?
  A: Ensure the mounting surface meets the specified requirements before proceeding with installation. Contact a professional if needed.

• Q: Can I install this product without turning off the electricity?
  A: No, it is crucial to shut off the electricity before starting any installation work to prevent the risk of electric shock or injury.

Item Number : A0518901

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instructions carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.

4. Place the wall switch in the “OFF” position.

5. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

6. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

7. Make sure the voltage you are using is 120V. The maximum wattage is LED, 12W.

8. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

9. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

10. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

• (A) Mounting plate (1)
• (B) Green ground screw (1)
• (E) Canopy screw (2)
• (F) Canopy (1)
• (G) Lock nut (1)
• (H) Cord (1)
• (I) Pipe (1)
• (J) Lampshade (1)
• (K) Connector (1)
• (L) Decorative ball (1)

ACCESSORIES & QTY ENCLOSED:

• (C) Plastic wire connector (3)
• (D) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power

3. Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

4. Go to the main fuse, or circuit breaker, box in your home.

5. Place the main power switch in the “OFF” position.

6. Place the wall switch in the “OFF” position.

7. Unscrew canopy screws (E) from canopy (F).

8. Remove mounting plate (A).

9. Screw pipe (I) to the top of lampshade (J).

10. Screw decorative ball (L) to connector (K) as shown in the illustration.

11. Attach mounting plate (A) to the outlet box with mounting screws (D).

12. Make wire connections
    Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
    Connect ground wires according to the chart below
    Connect wires according to the chart below

13. Twist wires together with plastic wire connectors until tightly joined.

14. Wrap each connector with approved electrical tape.

15. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

16. Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening canopy screws (E) onto the pre-assembled screws in mounting plate (A).
    Note : canopy (F) should be snug against the ceiling and canopy screws (E). If not, adjust the threaded length on mounting plate (A):

    • Unscrew the pre-assembled hex nuts.
    • Screw the pre-assembled screws in or out of mounting plate (A).
    • When the secure length is achieved, tighten the hex nuts and back to step 7.

17. To adjust the hanging height of the fixture:

18. Press down and hold lock nut (G) by hand.

19. Pull or push cord (H) in and out of canopy (F) to increase or decrease the hanging height.

20. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

+1 8638672245
service@lnchome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>