LNC 3QY6RVHD14331M7 2 Light Bronze Rustic Farmhouse Vanity Light Instruction Manual

LNC 3QY6RVHD14331M7 2 Light Bronze Rustic Farmhouse Vanity Light

Product Information

The product is a lamp fixture that requires installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury. The lamp fixture is designed to work with a maximum wattage of 40W per bulb, and the voltage used should be 120V. The lamp fixture should be kept away from acidic and alkaline substances that may damage its surface. When replacing bulbs, the lamp should be turned off or unplugged, and it must be allowed to cool down before replacing the bulbs. The safety instructions provided in the manual do not cover all possible conditions that may occur, and caution and care must be used with any electrical products.

Product Usage Instructions

1. Before starting assembly and installation, ensure that you have all the needed tools as shown in the picture.
2. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.
3. Turn off power before starting the installation by going to the main fuse or circuit breaker box in your home and placing the main power switch in the OFF position. Also, place the wall switch in the OFF position.
4. Make assembly by:
5. Unscrew knob nuts (F) from back plate (E), then setting them aside for later installation.
6. Carefully passing the supply wires from the outlet box through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
7. Connecting wires according to the below chart:
   Wire Color| Supply Wire| Fixture Wire
   ---|---|---
   Green or bare copper| Ground wire from outlet box| Green ground screw (D) on the mounting plate (C)
   Black or red| Supply wire with black or red insulation from outlet box| Socket (K) brass screw with black or red label
   White or gray| Supply wire with white or gray insulation from outlet box| Socket (K) silver screw with white or gray label

Please note that the ground wire is a bare copper wire, and it should never be connected to other wires.

4. Twisting wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Ensure that no wire strands are exposed and then carefully tucking all wires into the outlet box.
5. Aligning the holes in the back plate (E) with the preassembled mounting screws, then attaching back plate (E) to mounting plate (C) with the previously removed knob nuts (F). Hand tighten until snug.

5. The lamp fixture should be mounted on a clean, dry, flat, strong enough surface that is 1/4 larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16 should be corrected as required.
6. Ensure that the ceiling or wall can stand the weight of the lamp before installation.
7. When replacing bulbs, follow the instructions provided in the product information section.

Item Number: 3QY6RVHD14331M7

WARNING (To reduce the risk of fire, electric shock, or personal injury)

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “ OFF ” position.
   • Place the wall switch in the “ OFF ” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Back plate (1)
• (F) Knob nut (2)(H) Socket ring (2)
• (I) Sleeve (2)
• (J) Glass shade (2)
• (K) Socket (2)

ACCESSORIES ENCLOSED

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (G) Socket wrench (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “ OFF” position.
   • Place the wall switch in the “OFF” position.

3. Make assembly the socket.) Step A1: Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
   Step A2: Carefully pass the supply wires from the outlet box through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
   Step A3: Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES. Connect ground wires according to the below chart chart Connect wires according to the below Note: When parallel wires ( SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus. ) Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
   Step A4: Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back  plate (E) to mounting plate (C) with the previously removed knob nuts (F). Hand tighten until snug.
   NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (C) by unscrewing the preassembled hex nuts and then screwing the pre-assembled mounting screws in or out of mounting plate (C) until the secure length is achieved. Tighten the pre- assembled hex nuts and back to Step A4.
   Step A5:

   • Remove socket rings (H) and sleeves (I) from sockets (K).  Place glass shades (J) on sockets (K) and secure them with sleeves (I) and socket rings (H) using socket wrench (G).
   • Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

4. Check everything is installed properly, then you could turn on the light. Enjoy!
   CLEANING
   To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
   ORDERING PARTS
   Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>