LNC EJFZ32HD14076M7 Vintage Brushed Gold Bathroom Vanity Light Instruction Manual

LNC EJFZ32HD14076M7 Vintage Brushed Gold Bathroom Vanity Light

Product Information

This product is a lamp fixture that requires electrical installation and assembly. The lamp uses a maximum of 40W per bulb with a voltage of 120V. It comes with a mounting plate, backplate, knob nuts, arms, sockets, glass shades, socket rings, mounting screws, and plastic wire connectors. The product is designed to be mounted on a clean, dry, flat, and sturdy surface that is at least 1/4 larger than the canopy on all sides.

Product Usage Instructions

1. Before starting the installation, turn off the power by switching off the main power switch in the fuse or circuit breaker box in your home and the wall switch.
2. Check that all parts and accessories are included in the package.
3. Make wire connections as shown in the manual and make sure to connect the ground wire to the bare copper wire.
4. Secure the mounting plate to the outlet box using the mounting screws provided.
5. Attach the backplate to the preassembled mounting screws.
6. Screw the knob nuts onto the backplate.
7. Check that everything is properly installed before turning on the light.
8. When replacing bulbs, turn off or unplug the lamp and wait for it to cool before replacing the bulb. Keep the lamp away from acidic and alkaline substances that may damage the surface of the lamp.
9. Do not attempt any work without shutting off the electricity until the work is done. Make sure to use common sense, caution, and care with any electrical products.

Please note that we suggest installation by a licensed electrician. The safety instructions provided in this manual are not meant to cover all possible conditions that may occur.

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

• Before starting assembly and installation please prepare the needed tools as below picture.

PARTS INCLUDING

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Backplate (1)
• (F) Knob nut (2)
• (G) Arm (1)
• (H) Socket (4)
• (I) Glass shade (4)
• (J) Socket ring (4)

ACCESSORIES ENCLOSED

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • B) Place the wall switch in the “OFF” position.

3. Make assembly

• Step A1: Unscrew knob nuts (F) from the back plate (E), then set them aside for later installation.
• Step A2: Carefully pass the supply wires from the outlet box through the mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
• Step A3: Make wire connections Connect wires as the below wires connection shown.

PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

• Step A4: Align the holes in the back plate (E) with the preassembled mounting screws, then attach
  the back plate (E) to the mounting plate (D) with the previously removed knob nuts (F). Hand tightens until snug.
  NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of preassembled mounting screws on mounting plate assembly (D) by unscrewing the preassembled hex nuts and then screwing the preassembled mounting screws in or out of the mounting plate (D) until the secure length is achieved. Tighten the preassembled hex nuts and back to Step A4.

• Step A5: 1) Unscrew socket rings (J) from sockets (H). Fix glass shades (I) to sockets (H) with socket rings (J).

• Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is installed properly, then you could turn on the light. Enjoy

CLEANING

• To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

• Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

Support@ihomeangel.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>