LNC RUBUVZHD192W278 Light Brass Gold Bathroom Vanity Light Instruction Manual

October 30, 2023
LNC

LNC RUBUVZHD192W278 Light Brass Gold Bathroom Vanity Light

Product Information

This product is a lamp with item number RUBUVZHD192W278. It requires installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury. The maximum wattage for each bulb is Type T10, Max 60W. The lamp should be kept away from acidic and alkaline substances to prevent damage to its surface. When replacing bulbs, the lamp should be turned off or unplugged and allowed to cool down as bulbs get hot quickly. The safety instructions provided in the manual are not meant to cover all possible conditions that may occur, so caution and care must be used with any electrical products.
The product comes with a mounting plate, a green ground screw, a back plate, two knob nuts, two sockets, two glass shades, and two socket rings. It also includes two mounting screws and three plastic wire connectors.

Product Usage Instructions

  1. 1. Before starting the installation, turn off the power and never attempt any work without shutting off the electricity until the work is done.
  2. Secure the mounting plate to the outlet box with the mounting screws.
  3. Connect the wires according to the below chart:
Connect Black or Red Supply Wire to: Connect White Supply Wire to:
OUTLET BOX GROUND OUTLET BOX GROUND
FIXTURE GROUND DIMPLES
Green Ground Screw FIXTURE GROUND
Parallel cord (round & smooth) Clear, Brown, Gold or Black without tracer
Parallel cord (square & ridged) Insulated wire(other than green) with copper

conductor
Cupped Washer| Clear, Brown, Gold or Black with tracer
| Insulated wire(other than green) with silver conductor

  1. Twist the wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Make sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
  2. The lamp should be mounted on a ceiling or wall that can stand its weight. Any gap between the mounting surface and canopy exceeding 3/16 should be corrected as required.

INSTALLATION INSTRUCTION

Item Number: RUBUVZHD192W278
WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save them as you may need them at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home.
    • Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is Type T10, Max 60W per bulb.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

  • (C) Mounting plate (1)
  • (D) Green ground screw (1)
  • (E) Backplate (1)
  • (F) Knob nut (2)
  • (G) Socket (2)
  • (H) Glass shade (2)
  • (I) Socket ring (2)

ACCESSORIES ENCLOSED:

  • (A) Mounting screw (2)
  • (B) Plastic wire connector (3

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
  2. Turn off power
    • Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home.
    • Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  3. . Make assembly
  • Step A1 » Unscrew knob nuts (F) from back plate (E), then set them aside for later installation
  • Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (C). Secure mounting plate (C) to the outlet box with mounting screws (A).
  • Step A3 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

  • Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
  • Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
  • Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (C) with the previously removed knob nuts (F). Hand tighten until snug.
  • NOTE: back plate (E) should be snug against the wall with knob nuts (F).
  • If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C):
  • Unscrew the pre-assembled hex nuts.
  • Screw the pre-assembled mounting screws in or out of mounting plate (C).
  • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4

Step A5 »

  1. Remove socket rings (I) from sockets (G).
  2. Fix glass shades (H) to sockets (G) with socket rings (I).
  3. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
  4. Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper
support@ihomeangel.com

Documents / Resources

| LNC RUBUVZHD192W278 Light Brass Gold Bathroom Vanity Light [pdf] Instruction Manual
RUBUVZHD192W278, RUBUVZHD192W278 Light Brass Gold Bathroom Vanity Light, RUBUVZHD192W278 Gold Bathroom Vanity Light, Light Brass Gold Bathroom Vanity Light, Bathroom Vanity Light, Bathroom Light, Vanity Light, Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals