LNC Home A05056 Crystal Chandelier Instruction Manual
- June 1, 2024
- LNC HOME
Table of Contents
LNC Home A05056 Crystal Chandelier
Product Information
- Specifications:
- Item Number: A05056
- Max Voltage: 120V
- Max Wattage: LED, 12W
Product Usage Instructions
- Tools Required:
- Ladder
- Phillips Head Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
- Parts Type & Quantity:
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (O) Crystal-D (7)
- Accessories Included:
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
- (K) Crystal hook (2) (spare part)
- Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and check all parts and accessories.
- Make pre-installation checks, and use chain pliers to disconnect and discard unwanted parts.
- Turn off the power completely before starting the installation.
Connect wires as per the below chart:
| Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---|---
OUTLET BOX GROUND| GREEN GROUND SCREW|
FIXTURE GROUND| |
Note: Ground wire is bare copper wire, never connect other wires to ground wires.
FAQs
- Q: Can I install the product myself?
- A: We suggest installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury.
- Q: What is the maximum wattage for the LED lamp?
- A: The maximum wattage for the LED lamp is 12W.
- Q: How should I handle bulb replacements?
- A: When replacing bulbs, make sure to turn off or unplug the lamp and wait until it is cool as bulbs can get hot quickly.
PRODUCT INTRODUCTION
Item Number: A05056
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is LED, 12W. 7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. Itmust be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED
TOOLS REQUIRED (NOT INCLUDED): Before starting assembly and installation please prepare the needed tools as below picture.
PARTS DESCRIPTION
PARTS TYPE & QTY INCLUDING:
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Stud (2)
- (F) Canopy (1)
- (G) Loop (2)
- (H) Quick link (2)
- (I) Chain (1)
- (J) Body assembly (1)
- (K) Crystal Hook (35)
- (L) Crystal-A (7)
- (M) Crystal-B (7)
- (N) Crystal-C (14)
- (O) Crystal-D (7)
OUTLET BOX
ACCESSORIES & QTY ENCLOSED:
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
- (K) Crystal hook (2) (spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
- Step A1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted parts.
- Step A2 » Carefully pull wire upward from canopy (F) and stop just at the proper place. Gently pull the wires to ensure the wires are not stressed.
- Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Make installation
- Step B1 » Unscrew studs (E) from the canopy (F) and then remove mounting plate (C).
- Step B2 » Attach mounting plate (C) to the outlet box with mounting screws (B).
- Step B3 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step B4 » Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening studs (E) onto the assembled screws in mounting plate (C).
- Step B5 »
- String crystal hooks (K) onto holes of the crystal.
- Hang crystals to holes of body assembly (J) as shown in the illustration.
- Check everything is already installed properly, and then you can turn on the light. Enjoy!
ORDERING PARTS
- Keep this sheet for future reference in case you need to order replacement parts.
- All parts for this fixture can be ordered from the place of purchase.
- Be sure to use exact wording from illustrations when ordering parts.
CLEANING
- To clean, wipe the fixture with a soft cloth.
- Clean glass with a mild cleaner (such as mild and non-abrasive soap).
- Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>