LNC A05286 Digipurve 23.6 in 3 Light Polished Gold Instruction Manual

May 15, 2024
LNC

LNC A05286 Digipurve 23.6 in 3 Light Polished Gold

Specifications

  • Item Number: A05286
  • Voltage: 120V
  • Maximum Wattage: Type B, Max 40W per bulb

Product Usage Instructions

Warnings and Precautions To ensure the safety and proper functioning of the product, please adhere to the following warnings and precautions:

  • Installation should be done by a licensed electrician.
  • Read the instructions carefully and keep them for future reference.
  • Always shut off electricity before starting any work.
  • Ensure the mounting surface is clean, dry, flat, and strong enough.
  • Verify the weight capacity of the ceiling or wall for the lamp.
  • Avoid contact with acidic or alkaline substances.
  • When replacing bulbs, turn off or unplug the lamp and allow it to cool down.

FAQ

  • Q: Can I use bulbs with a wattage higher than 40W per bulb?
  • A: No, the maximum wattage per bulb recommended is 40W to prevent overheating and damage to the fixture.
  • Q: What should I do if there are gaps between the mounting surface and canopy?
  • A: Any gaps exceeding 3/16 should be corrected before installation to ensure stability and proper fitting of the fixture.
  • Q: Can I connect other wires to the ground wire?
  • A: Never connect other wires to the ground wire. Follow the provided chart for correct wire connections.

Introductions

Item Number: A05286
WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.

  2. Please read the instruction carefully and save it as you may need it at a later time.

  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home.
      Place the main power switch in the “OFF” position.

    • Place the wall switch in the “OFF” position.

  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

  6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.

  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

LNC-A05286-Digipurve-23-6-in-3-Light-Polished-Gold-
fig-1

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED)

  • Before starting assembly and installation please prepare the needed tools as below picture.

LNC-A05286-Digipurve-23-6-in-3-Light-Polished-Gold-
fig-2

PARTS INCLUDED

  • (C) Green ground screw (1)

  • (D) Mounting plate (1)

  • (E) Back plate (1)

  • (F) Knob nut (2)

  • (G) Socket (3)

  • (H) Fixing screw (9)

  • (I) Lampshade (3)
    ACCESSORIES ENCLOSED

  • (A) Mounting screw (2)

  • (B) Plastic wire connector (3)

  • (H) Fixing screw (1) (spare part)

LNC-A05286-Digipurve-23-6-in-3-Light-Polished-Gold-
fig-3

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home.
      Place the main power switch in the “OFF” position.

    • Place the wall switch in the “OFF” position.

  3. Make assembly

LNC-A05286-Digipurve-23-6-in-3-Light-Polished-Gold-
fig-4

  • Step A1: Unscrew knob nuts (F) from back plate (E) and mounting plate (D), then set them aside for later installation.
  • Step A2: Carefully pass the supply wires from the outlet box through mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
  • Step A3: Make wire connections

Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the chart below

LNC-A05286-Digipurve-23-6-in-3-Light-Polished-Gold-
fig-5

Connect wires according to the chart below

LNC-A05286-Digipurve-23-6-in-3-Light-Polished-Gold-
fig-7

Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step A4: Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.

NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (D):

  • Unscrew the pre-assembled hex nuts.
  • Screw the pre-assembled mounting screws in or out of mounting plate (D).
  • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.

Step A5

  1. Remove fixing screws (H) from sockets (G).
  2. Align holes of lampshades (I) and holes of sockets (G).
  3. Screw fixing screws (H) into holes to secure lampshades (I).
  4. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

  • Keep this sheet for future reference in case you need to order replacement parts.
  • All parts for this fixture can be ordered from the place of purchase.
  • Be sure to use exact wording from illustration when ordering parts.

CLEANING

  • To clean, wipe the fixture with a soft cloth.
  • Clean glass with a mild cleaner (such as mild and non-abrasive soap).
  • Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals