LNC FZMI2YHD13409B6 Modern Gold Bathroom Vanity Light Instruction Manual
- October 30, 2023
- LNC
Table of Contents
FZMI2YHD13409B6 Modern Gold Bathroom Vanity Light
Instruction Manual
FZMI2YHD13409B6 Modern Gold Bathroom Vanity Light
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as
below picture
PARTS INCLUDING:
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Back plate (1)
(F) Ball knob (2)
(G) Fixture body (1)
(H) Socket (3)
(I) Glass shade (3)
ACCESSORIES ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)
ASSEMBLY&INSTALLATION INSTRUCTION
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
-
Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done.
A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B). Place the wall switch in the “OFF” position. -
Make assembly
Step A1 : Unscrew the ball knob(F) from the back plate(E) then gently
remove the mounting plate (D).
Step A2: Secure mounting plate (D) to outlet box with mounting screws
(A).
Step A3: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF
FIXTURE, NEVER CONNECT WIRE TO GROUND WIRE
Connect ground wire according to below chart
Connect wires according to below chart
Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
---|---|
Black | White |
*Parallel cord ( round & smooth ) | *Parallel cord ( square & ridged ) |
Clear,Brown,Gold or Black without tracer | Clear,Brown,Gold or Black with |
tracer
Insulated wire ( other than green) with copper conductor| Insulated wire (
other than green ) with silver conductor
*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus. )
Twist plastic wire connector until wires are tightly joined together, wrap
each connector with approved electrical tape. Be sure that no wire strands are
exposed and then carefully tuck all wires into the outlet box .
Step A4: Align the holes in the back plate (E) with the mounting screws, then
attach the back plate (E) using the previously removed ball knob (F). Hand
tighten until snug.
Step A5: Install bulbs (Not included. Please do not exceed the maximum
capacity recommended on the socket.)
Twist the glass shade (I) on the joint on socket (H).
4.Check everything installed properly, then you could turn on the light.
Enjoy!
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>