LNC 2QB3UVHD14733S7 Classic 6 Inch 1 Light Black Wall Sconce Instructions
- October 30, 2023
- LNC
Table of Contents
LNC 2QB3UVHD14733S7 Classic 6 Inch 1 Light Black Wall Sconce
Product Information
- Product Name: Unknown
- Manufacturer: iHome Angel
- Contact Information: support@ihomeangel.com
- Parts Included: Green ground screw (1), Mounting plate (1), Backplate (1), Ball knob (2), Socket (1), Iron lampshade (1), Socket ring (1)
- Accessories Enclosed: Mounting screw (2), Plastic wire connector (3)
Product Usage Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off the power before starting installation. Go to the main fuse or circuit breaker box in your home and place the main power switch in the OFF position. Place the wall switch in the OFF position as well.
- Make assembly:
- Unscrew the ball knobs (F) from the back plate(E) then gently remove the mounting plate (D).
- Secure mounting plate (D) to outlet box with mounting screws (A).
- Connect wires according to the chart provided, making sure to twist the plastic wire connector until the wires are tightly joined together. Wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Align the holes in the back plate (E) with the mounting screws, then attach the back plate (E) using the previously removed ball knobs (F). Hand tightens until snug.
- Fix the iron lamp shade (H) to the socket (G) with the socket ring (I). Install bulbs (Not included. Please do not exceed the maximum capacity recommended on the socket.)
- Check everything is installed properly, then you could turn on the light and enjoy!
WARNING: To reduce the risk of fire, electric shock, or injury to persons:
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save them as you may need them at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
Cleaning: To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
Ordering Parts: Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before the fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing the bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before doing assembly and installation please prepare the needed tools as
below picture 
PARTS INCLUDING
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Backplate (1)
- (F) Ball knob (2)
- (G) Socket (1)
- (H) Iron lampshade (1)
- (I) Socket ring (1)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
- Turn off power Before you start to make an installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “ OFF ” position. B). Place the wall switch in the “ OFF ” position.
- Make assembly
- Check everything is installed properly, then you could turn on the light. Enjoy!
- CLEANING To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
- ORDERING PARTS Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
- Step A1: Unscrew the ball knobs (F) from the back plate(E) then gently remove the mounting plate (D).
- Step A2: Secure mounting plate (D) to the outlet box with mounting screws (A).
- Step A3: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF
FIXTURE, NEVER CONNECT WIRE TO GROUND WIRE Connect ground wire according to
below chart Connect wires according to below chart
Note: When parallel wires ( SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus. )
Twist the plastic wire connector until wires are tightly joined together, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in the back plate (E) with the mounting screws,
then attach the back plate (E) using the previously removed ball knobs (F).
Hand tightens until snug.
Step A5 :Fix the iron lamp shade (H) to the socket (G) with the socket
ring (I). Install bulbs (Not included. Please do not exceed the maximum
capacity recomended on the socket.
support@ihomeangel.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>