LANCOM SYSTEMS VPN 1900EF Router Instruction Manual

: June 4, 2024
: LANCOM SYSTEMS

Table of Contents

Mounting & connecting
LED description & technical details
Documents / Resources

Hardware Quick Reference
LANCOM 1900EF

Mounting & connecting

➀ WAN 1 interfaces (SFP / TP combo port)
Insert a suitable SFP module (e.g. 1000Base-SX or 1000Base-LX) into the SFP port. Choose a cable compatible with the SFP module and connect it as
described in the module’s documentation. SFP module and cable are not included.
If desired, alternatively connect the WAN 1 TP interface to a WAN modem using the provided Ethernet cable with green connectors.

➁ WAN 2 interface (TP)
Connect the WAN 2 interface to a WAN modem using the provided Ethernet cable with green connectors.

➂ Ethernet interface
Use the cable with the kiwi-colored connectors to connect one of the interfaces ETH 1 to ETH 4 to your PC or a LAN switch.

➃ Configuration interface
To configure the device via the serial interface, a serial configuration cable is required (available as an accessory).

➄ USB interface
You can use the USB interface to connect a USB printer or a USB storage device.

➅ Power connector and grounding point (device back side)
➆ Supply power to the device via the power connector. Please use the IEC power cable supplied (separately available for WW devices).
ATTENTION: High touch current possible! Connect to earth before connecting the power supply.

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

Please observe the following when setting up the device

The mains plug of the device must be freely accessible.
For devices to be operated on the desktop, please attach the adhesive rubber footpads
Do not rest any objects on top of the device and do not stack multiple devices
Keep all ventilation slots of the device clear of obstruction
Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets. Pay attention to the “R” and “L” marks on the brackets for accurate mounting.

LED description & technical details

➀ VPN / POWER

VPN Off	VPN connection inactive
Green, permanently	VPN connection active
Green, flashing	VPN connecting
POWER Off	Device switched off
Green, permanently*	Device operational, resp. device paired / claimed and

LANCOM Management Cloud (LMC) accessible
Green / red, blinking| No password set. Without a password the configuration data in the device is unprotected.
Red, blinking| Charge or time limit reached
1x green inverse
blinking| Connection to the LMC active, pairing OK, device not claimed
2x green inverse blinking| Pairing error, resp. LMC activation code not available
3x green inverse blinking*| LMC not reachable resp. communication error

➁ RESET

Reset button| short press > Restart the device
long press > Reset the device
---|---

➂ WAN 1 / WAN 2

Green, orange off	No networking device connected
Green, permanently	Connection to network device operational, no data traffic
Green, flickering	Data transmission
Orange off	1000 Mbps
Orange, permanently	10 / 100 Mbps

➃ ETH 1 – ETH 4

Green, orange off	No networking device connected
Green, permanently	Connection to network device operational, no data traffic
Green, flickering	Data transmission
Orange off Orange, permanently	1000 Mbps 10 / 100 Mbps
Hardware
---	---
Power supply	Internal power supply unit (100-240 V, 50-60 Hz)
Power consumption	Max. 18 W
Environment	Temperature range 0-40 °C, humidity 0-95 %; non-condensing
Housing	Robust metal housing, 1 HU with mounting brackets for 19″

installation, 345 x 44 x 253 mm (W x H x D)
Number of fans| None; fanless design, no rotating parts, high MTBF
Interfaces|
WAN 1 / WAN 2| WAN 1 SFP: Compatible with optional LANCOM SFP modules. Set as a WAN port ex-factory, can be configured as a LAN port.
WAN 1 / WAN 2 TP: 10 / 100 / 1000 Base-TX, autosensing full duplex (WAN 1) / autosensing (WAN 2). auto node hub
ETH1 – ETH 4| 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode. Up to 3 ports can be operated as additional WAN ports. Ethernet ports can be electrically disabled in the LCOS configuration.
Confiq (Com) / V.24| Serial configuration interface / COM-port: 9,600 – 115,200 baud
USB| USB 2.0 hi-speed host port for connecting USB printers (USB print server), serial devices (COM-port server) or USB drives (FAT file system)
WAN protocols|
Ethernet| PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without DHCP), RIP-1, RIP-2, VLAN, GRE, EoGRE, L2TPv2 (LAC or LNS), IPv6 over PPP (IPv6 and
IPv4/1Pv6 dual stack session), IP(v6)oE (autoconfiguration, OHCPv6 or static)
Package content|
Cables| 1 Ethernet cable, 3 m (kiwi colored connectors); 1 Ethernet cable, 3 m (green connectors);
1 IEC Dower cord 230 V (not for WW devices)
Mounting brackets| Two 19″ brackets for rack mounting

*) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management
Cloud.

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc/

LANCOM, LANCOM Systems, LCOS, LANcommunity, and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements
relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions.

111654/0622