LANCOM SYSTEMS QT60 AirLancer Instruction Manual
- June 3, 2024
- LANCOM SYSTEMS
Table of Contents
LANCOM Antenna
AirLancer ON-QT60 / ON-QT90
Instruction Manual
MOUNTING INSTRUCTIONS
Mounting kit contents
| 1 Connection flange (A) | 6 Spring washers M5 (E) |
|---|---|
| 1 Connection arm (B) | 6 Washers M5 (F) |
| 1 Pole flange / wall bracket (C) | 6 Nuts M5 (G) |
| 2 Hexagon head screws M5x25 (D) | 2 Band clamps 2,5“ (H) |
Mounting the antenna flange
Screw the connection flange A to the back of the antenna housing using the
enclosed washers F, lock washers E and nuts G. Make sure that the spring
washers E are located
directly under the nuts.
Then fasten the connecting arm B hand-tight to the connecting flange using a
screw D, a spring washer E, a washer F, and a nut G.
Make sure that the spring washer E is located directly under the screw head.
Preparation for wall mounting
If you want to mount the antenna on a wall, use the wall mount C as a drilling
template to mark the drill holes for wall mounting.
Drill the corresponding holes at the markings and insert dowels (not included)
into them if necessary. Depending on the wall material and condition, the
depth and diameter of the holes must be adjusted.
Wall mounting of the antenna
Align the wall bracket with the drill holes and fasten it with suitable
screws.
Now fasten the connecting arm B, which is already mounted on the antenna, to
the connecting flange hand-tight using a screw D, a spring washer E, a washer
F, and a nut G.
Make sure that the spring washer E is directly under the screw head and that
the cables of the antenna point downwards.
Align the antenna according to your wishes and then tighten the screws of the
connection arm with suitable torque.
Pole mounting of the antenna
Position the pole flange C at the desired height on a suitable pole with
sufficient load-bearing capacity and a diameter between 40 and 64 mm.
Then, as shown in the overview, guide the two band clamps H through the pole
flange C and around the pole and tighten them after aligning the pole flange.
Then connect the pole flange C hand-tight to the connecting arm B mounted on
the antenna by means of an enclosed screw D, a washer F, a spring washer E,
and a nut G.
Make sure that the spring washer E is located directly under the screw head.
Align the antenna according to your requirements and then tighten the screws
of the connection arm with suitable torque.
|
---|---
Important information
Responsible handling of high frequency
In order to comply with the protection requirements of EU Directive 2014/53
and EN 62479 with regard to the basic restrictions for the safety of persons
in electromagnetic fields and the „FCC Policy on Human Exposure to
Radiofrequency Electromagnetic Fields“, it is necessary to configure the
correct antenna gain in the WLAN router or WLAN access point.
Important information
Electrical and Electronic Equipment Act
Please do not dispose of electrical and electronic waste in household waste,
where it cannot be recycled. Make sure that your electrical and electronic
waste is disposed of in accordance with the currently valid guidelines of your
country.
Important information
Correct handling of antenna cables
Antenna cables are sensitive RF cables. When laying them, it is therefore
important to ensure that the cables are not kinked and are bent as little as
possible, as this can result in losses in terms of antenna performance.
Likewise, the antenna cables should not be wound into tight cable loops.
Important information
Antenna gain and termination of unused antenna ports on access points
Unused antenna connections on the access point must be terminated with an
enclosed rod antenna. For indoor access points, the terminating resistor
included with the AirLancer AN-RPSMA-NJ adapter can be used. In addition, the
antenna gain must be specified in the configuration of the access point.
| Technical data | ON-QT60 | ON-QT90 |
|---|---|---|
| Frequency range | 2,400 – 2,500 MHz, 4,900 – 7,125 MHz |
Antenna characteristics
Radiation patterns| Horizontally 2.4 GHz: 60°
Vertically 2.4 GHz: 60°
Horizontally 5 GHz: 60°
Horizontally 5 GHz: 60°| Horizontally 2.4 GHz: 95°
Vertically 2.4 GHz: 97°
Horizontally 5 GHz: 99°
Horizontally 5 GHz: 60°
Recommended use| Point-to-Multipoint, Sector
VSWR| 2.0:1 max.
Gain| 2.4 GHz: 7 dBi max.
5 GHz: 7 dBi max.| 2.4 GHz: 6 dBi max.
5 GHz: 6 dBi max.
Mechanical Data
Dimensions (mm)| 233.7 x 183.7 x 40 (B x H x T)
Weight| 900 g (Antenna without mounting kit)
Operating temperature| -40 °C to 85 °C
Color| Light grey
Material| UV resistant plastic
Mounting options| Wall and pole mounting, alignable
Cables & Connectors| 4x 100 cm ULA100 cable with N-Plug connector
Item
Warranty| 2 years for AirLancer and accessories
Item no.| 61263| 61264
Scope of delivery| Antenna, mounting kit for wall and pole mounting
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/ or omissions. 112149/0322
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>