SCHLAGE J-Series Non Turning Dummy Knob, Lever Instruction Manual

]SCHLAGE J-Series Non Turning Dummy Knob, Lever

Product Information

The product is a set of levers or knobs that can be installed on doors. The finish of the levers or knobs can last longer if the following requirements are observed  Do not install levers or knobs before doors are painted.

• Refrain from using cleansers or acid chemicals to polish your levers or knobs to avoid oxidation.
• Do not use heavy or sharp-edged objects to scrub levers or knobs.

The package includes a template for easy installation. The backset distance can be either 2-3/8 inches (60 mm) or 2-3/4 inches (70 mm). A removal tool is also included for easy knob or lever removal.

Product Usage Instructions

Tools Needed for New Installation Service

Before installing the levers or knobs, ensure that the doors are painted and ready for installation. Avoid using cleansers or acid chemicals to polish the levers or knobs to prevent oxidation. Also, refrain from using heavy or sharp- edged objects to scrub the levers or knobs.

Cut Along the Dotted Line to Remove the Template Replacement Installation

1. Use the template to draw a center line for the dummy lever or knob across the edge of the door, approximately 36 inches (91 4mm) above the floor.
2. Align the edge of the template with the edge of the door after measuring for the required backset distance. Match the center line with the center line drawn on the door edge.
3. Mark and drill two 1/8 inch (3.17 mm) holes by 1 inch (2.54 cm) deep.
4. Remove the knob or lever for ease of installation.

A knob or Lever Removal

Use the removal tool to push into the hole in the neck of the rose against the catch while pulling the knob or lever off the spindle.

Chassis Installation

1. Place the chassis on the door face over the drilled holes.
2. Ensure that the catch hole faces the door edge.
3. Insert the two (S1) wood screws through the screw holes in the rose and tighten firmly.

Install Knob or Lever

1. Align the slot in the knob or lever with the hole pattern in the spindle as shown.
2. Slide the knob or lever down the spindle until it clicks into place. Test for proper installation by pulling.

Note
For more detailed instructions, refer to the product manual included in the package

User Manual

Installation and Removal

Installing your device

•  Place the tablet in the bottom of the case.

• Then press the top half of the tablet into the case until you feel it snap in place Removing your device:
  

•  Hold the tablet on opposite corners as indicated in the picture below, and use your thumb in the bottom corner to GENTLY push up the tablet.

•  Gently remove the tablet from the case. Pairing

Pairing Instructions

•  Turn on the Keyboard using the toggle switch on the right side.
•  The Keyboard will automatically enter pairing mode when turned on for the first time.
•  Select Settings -> Connected devices -> Pair new device.
•  Select “Fintie Keyboard” from the list of Available devices.
• If “Fintie Keyboard” is not available, press “Fn+C” for “Fintie Keyboard” to become available and then select from the list of Available devices.
•  Select ”Pair” to complete the pairing.

Sleep Mode

The keyboard will enter sleep mode after being idle for 30 minutes. Press any keyto wake the keyboard up. Wait up to 2 seconds for the keyboard to reconnect with
the tablet before starting to type.

Charging Your Keyboard

1.  Plug the Type-C end of the charging cable into the keyboard and the other USB end into your preferred USB charger. (USB charger is not included.)
2.  When charging, the power indicator will turn red. Generally, it takes approximately 2.5 hours for a full charge. (Output: DC 5V/500mA.) Package Contents

Package Contents

• 1 x Keyboard Case
• 1 x USB-C Charging Cable
• 1 x User Manual

Specifications

Product Overview

1. Power indicator:  Turns blue for 3 seconds.
   Bluetooth indicator :  Flashes blue when pressing “Fn + C”.
   Caps Lock indicator: Blue light is on.

2. Charging indicator: Red while charging. Green when fully charged.
   Low battery indicator: Flashes red when charging is required.

3. Charging port: Only used for charging.

Keys and Function

Tip : Press Fn key and hot key together to activate action

Troubleshooting

1. If your device does not respond to the keyboard, try the following.
2.  On your Fire HD 10, navigate to “Settings > Connected Devices > Previously connected devices” and delete any entries for unused Bluetooth devices including “Fintie Keyboard”.
3.  Restart your device.
4.  Turn your keyboard off and back on.
5.  Forget and re-pair your keyboard.
6.  If your keyboard does not establish or maintain a Bluetooth connection, reset the Bluetooth module by charging your keyboard.
7.  If your keyboard does not operate correctly after charging it, please contact your authorized retailer.

Safety Tips

• Do not place heavy objects on the keyboard.
•  Do not disassemble the product.
•  Keep the product away from oils, chemicals, and organic liquids.
•  Use only a damp, soft cloth, like a microfibre, to wipe the keyboard.
•  Dispose of the battery according to local laws.

For UK customers only
Recycling Your Old Electricals Is Easy!
Recycle your electrical and electronic devices for free at your local recycling center. To find your nearest center, visit www.recycle-more.co.uk and type in your postcode.

Why Recycle?
Unwanted electrical equipment is the UK’s fastest-growing type of waste. Many electrical items can be repaired or recycled, saving natural resources and the environment. If you do not recycle, electrical equipment will end up in landfill where hazardous substances will leak out and cause soil and water contamination–harming wildlife and also human health. We’re proud to support your local authority in providing local recycling facilities for electrical equipment. To remind you that old electrical equipment can be recycled, it is now marked with the crossed-out wheeled bin symbol. Please do not throw any electrical equipment (including those marked with this symbol) in your bin.

What is WEEE?

The Waste Electrical or Electronic Equipment (WEEE) Directive requires countries to maximize separate collection and environmentally friendly processing of these items.

How Are We Helping?
In the UK, distributors including retailers must provide a system that allows all customers buying new electrical equipment the opportunity to recycle their old items free of charge. As a responsible retailer, we have met the requirements placed on us by financially supporting the national network of WEEE recycling centers established by local authorities. This is achieved through membership of the national Distributor Take-back Scheme (DTS). To find more information on WEEE recycling and to locate your nearest recycling center, please visit www.recycle.more

Contact Us
Website : www.fintie.com
E-mail : support@fintie.com

North America

Tel: 1-888-249-8201 (Monday-Friday: 9:00 AM – 5:00 PM EST) Europe
Tel: +49 69 95094777 (Monday-Friday: 9:00 AM – 5:00 PM CET)

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver.
•  Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1.  this device may not cause harmful interference
2.  this device must accept any interference received, including interference that may cause undesired operation

IC Caution

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s ).
Operation is subject to the following two conditions :

1.  This device may not cause interference.
2.  This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>