LANCOM Systems GS-3528X Multi Gigabit Ethernet Access Switch User Guide
- June 4, 2024
- LANCOM SYSTEMS
Table of Contents
LANCOM Systems GS-3528X Multi Gigabit Ethernet Access Switch
Installation Steps
Configuration interface (Console)
- Connect the configuration interface via the included serial configuration cable to the serial interface of the device you want to use for configuring / monitoring the switch.
TP Ethernet interfaces
- Use Ethernet cables to connect the interfaces 1 to 24 to your PC or a LAN switch.
SFP+ interfaces
- Insert suitable LANCOM SFP modules into the SFP+ interfaces 25 to 28. Choose cables which are compatible with the SFP modules and connect them as described in the module’s documentation.
Power connector (device back side)
- Supply power to the device via the power connector. Please use the IEC power cable supplied or a country-specific LANCOM Power Cord.
Please observe the following when setting up the device
- The mains plug of the device must be freely accessible.
- For devices to be operated on the desktop, please attach the adhesive rubber footpads.
- Do not rest any objects on top of the device and do not stack multiple devices.
- Keep the ventilation slots on the side of the device clear of obstruction.
- Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide! Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times
a System ****
System: off| Device switched off
System: green| Device operational
System: red| Hardware error
b Reset button|
_~5 sec. pressed_| Device restart
7~12 sec. pressed| Configuration reset and device restart
c TP Ethernet por| ts 10M / 100M / 1G
LEDs switched to Link/Act/Speed mode
Off| Port inactive or disabled
Green| Link 1000 Mbps
Green, blinking| Data transfer, link 1000 Mbps
Orange| Link < 1000 Mbps
_Orange, blinking_ | Data transfer, link < 1000 Mbps
LEDs switched to PoE mode
__Off | Port inactive or disabled
Green| Port enabled, power supply to connected device
Orange| Hardware error
d TP Ethernet po| rts 100M / 1G / 2.5G **
---|---
LEDs switched to Link/Act/Speed mode**
__Off | Port inactive or disabled
_Green_| Link 2500 Mbps
_Green, blinking_ | Data transfer, link 2500 Mbps
__Orange| Link < 2500 Mbps
Orange, blinking | Data transfer, link < 2500 Mbps
LEDs switched to PoE mode
__Off | Port inactive or disabled __
Green| Port enabled, power supply to connected device
Orange| Hardware error
e 10 G SFP+ port| s
Off| Port inactive
__Blue| Link 10 Gbps
Green| Link 1000 Mbps
**Hardware **|
---|---
Power supply| Internal power supply unit (110–230 V, 50–60 Hz)
Power consumption| max. 50 watts
Environment| Temperature range 0–40°C; short-term temperature range 0–50°C;
humidity 10–90%; non-condensing
Housing| Robust metal housing, 19“ 1U (442 x 44 x 375 mm > W x H x D) with
removable mounting
__brackets, network connectors on the front
Number of fans| 1
**Interfaces **
ETH| A 12 TP Ethernet ports 10 / 100 / 1000 Mbps
A 12 TP Ethernet ports 10 / 100 / 2500 Mbps
A 4 SFP/SFP+ ports 1 / 10 Gbps
A 28 concurrent Ethernet ports in total
**Declaration of Conformity **
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen,
declares that this device is in compliance with Directives 2014/30/EU,
2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of
the EU Declaration of Conformity is available at the following Internet
address: www.lancom-systems.com/doc
**Package Content **
Documentation | Quick Reference Guide (DE/EN), Installation Guide
(DE/EN)
Mounting brackets| Two 19” brackets for rackmounting
Cable| 1 IEC power cord, 1 serial configuration cable 1.5 m
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>