LANCOM Systems 1780EW-4G+ High Performance Mobile VPN Router User Guide
- June 4, 2024
- LANCOM SYSTEMS
Table of Contents
LANCOM Systems 1780EW-4G+ High Performance Mobile VPN Router
- Before initial startup, please make sure to take notice of the information regarding the intend-ed use in the enclosed installation guide!
- Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
- The SIM card may only be inserted or removed when the device is switched off. Inserting or removing the SIM card when the device is switched on can destroy the 4G module!
- Antennas may only be mounted or replaced when the device is switched off.
- Mounting or removing the antennas when the device is switched on can destroy the 4G or Wi-Fi modules!
Please observe the following when setting up the device
- The power plug of the device must be freely accessible.
- For devices to be operated on the desktop, please attach the adhesive rubber footpads
- Do not rest any objects on top of the device
- Keep all ventilation slots on the side of the device clear of obstruction
- In case of wall mounting, use the drilling template as supplied
- Rack installation with the optional LANCOM Rack Mount (separately available)
- In the case of separately purchased antennas, ensure that the permissible transmission power of the system is not exceeded. The operator of the system is responsible for compliance with the limits.
PARTS INSTRUCTIONS
-
LTE / 4G antennas
Connect the two supplied cellular antennas to the connectors located at the device‘s sides.
-
GPS antenna (optional)
Connect the GPS antenna (free of charge) to the connector GPS (see included voucher).
-
WLAN antennas
Screw the two supplied WLAN antennas onto the connectors WLAN Ant 1 and WLAN Ant 2. The desired MIMO behavior can be configured underPhysical WLAN Settings > Radio > Antenna grouping
-
Power
When connecting the cable to the device, turn the bayonet connector 90° clockwise until it clicks into place. Use only the supplied power adapter. -
Serial interface
Configuring the device via the serial interface requires a serial configuration cable (available as an accessory).
-
WAN interface
Use the cable with the green-colored connectors to connect the interface ETH2 to your WAN modem. -
Ethernet interface
Use the cable with the kiwi-colored connectors to connect the interface ETH1 (PoE) to your PC or a LAN switch. -
Optional: SIM card
Slide the SIM card into the slot using the marker to ensure that the card is the right way round. Ensure that the SIM card clicks into place on insertion. To remove the card from the device again, press the card lightly into the device. Let go to release the SIM card from the slot.
Mounting & connecting
- The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud.
- This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL).
- The license information for the device firmware (LCOS) is available on the device‘s WEBconfig interface under “Extras > License information“.
- If the respective license demands, the source files for the corresponding software components will be made available on a down-load server upon request.
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen,
declares that this device is in compliance with Directives 2014/30/EU,
2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006.
The full text of the EU Declaration of Conformity is available at the
following Internet address: www.lancom-systems.com/doc
Please respect the restrictions which apply in your country when setting up an
antenna system (in particular the antenna gain and transmission power). For
information about calculating the correct antenna setup, please refer to www
.lancom-systems.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>