ROLLINGSQUARE EKIT01 EDGE Full Kit User Manual

Table of Contents

Specifications

EDGE Mount:
- Weight: 34 gr / 1.1 oz
- Size: 115X30X4.5 mm / 4.5X1.1X1.7 in
- Materials: CNC machined aluminum, with N52 magnets and an ultra gripping layer on the front surface
EDGE Wireless Charger:
- Input: 5V/2A, 9V/2A, 12V/1.5A
- Output: 7.5W / 10W / 15W
- Weight: 38 gr / 1.3 oz
EDGE Light:
- Brightness: 280 lumens with x3 levels of control
- Input: 5V / 1A
- Battery Capacity: 140mAh / 0.5Wh
- Weight: 35gr / 1.2oz

EDGE Mount

Use the Magnetic Disc Aligner to stick the Magnetic Disc (A) on the back of your phone.
Remove the nano suction’s protective film.
Clean the surface of the device before proceeding.
Open the EDGE Mount and snap your phone on it, find the position you prefer on your device and push part B for 10 seconds to fix it in place.
To remove the EDGE Mount, pry with EDGE Remover on the lower right side. Never pull the EDGE Mount from part C.

EDGE Wireless Charger

Use the Magnetic Disc Aligner to stick the Magnetic Disc (A) on the back of your phone (not needed for iPhone 12 or later). To center it, use the Magnetic Disc Aligner.
Snap the EDGE Wireless Charger to the EDGE Mount and plug the USB-C connector into a USB-C power source.
Snap your phone to the EDGE Wireless Charger to start charging your phone.

EDGE Light

Snap the EDGE Light to the EDGE Mount and click the button to light it up.
The first three clicks change the light intensity and the fourth turns it off.
The EDGE Light works for 55 minutes at medium intensity when fully charged.
To recharge the EDGE Light, use the USB-C to USB-C cable provided in the pack. You can also keep it plugged in while using it.

FAQ

Q: Can I submerge the device in water?
A: No, avoid submerging the device in water or exposing it to adverse weather conditions.
Q: How long does the EDGE Light work when fully charged?
A: The EDGE Light works for 55 minutes at medium intensity when fully charged.

User Manual

EDGE® Full Kit

$ROLLINGSQUARE-EKIT01-EDGE-Full-Kit- $1$$

EDGE® Mount $ROLLINGSQUARE-EKIT01-EDGE-Full-Kit- $2$$

Use the Magnetic Disc Aligner to stick the Magnetic Disc (A) on the back of your phone.
Remove the nano suction’s protective ﬁlm.
Clean the surface of the device before proceeding. Open the EDGE Mount and snap your phone on it, ﬁnd the position you prefer on your device and push part B for 10 seconds to ﬁx it in place.
To remove the EDGE Mount pry with EDGE Remover on the lower right side. Never pull the EDGE Mount from part C.

$ROLLINGSQUARE-EKIT01-EDGE-Full-Kit- $3$$

Use the Magnetic Disc Aligner to stick the Magnetic Disc (A) on the back of your phone (not needed for iPhone 12 or later). To center it, use the Magnetic Disc Aligner.
Snap the EDGE Wireless Charger to the EDGE Mount and plug the USB-C connector in a USB-C power source.\
Snap your phone to the EDGE Wireless Charger to start charging your phone.

$ROLLINGSQUARE-EKIT01-EDGE-Full-Kit- $4$$

Snap the EDGE Light to the EDGE Mount and and click the button to light it up. The ﬁrst three clicks change the light intensity and the fourth turns it off.
The EDGE Light works for 55 minutes at medium intensity when fully charged. To recharge the EDGE Light use the USB-C to USB-C cable provided in the pack. You can also keep it plugged in while using it.

ROLLING SQUARE ® is a trademarks of Ferraris Group Sagl / Corso San Gottardo 99, Chiasso CH 6830, Switzerland / +41 091 2347763

Warnings

KEEP THE DEVICE OUT OF REACH OF CHILDREN.
KEEP THE DEVICE AWAY FROM FIRE AND HIGH TEMPERATURE.
AVOID DROPPING THE DEVICE.
DO NOT SUBMERGE IN WATER OR EXPOSE TO ADVERSE WEATHER CONDITIONS.
DO NOT OPEN OR PUNCTURE IT.
DO NOT DISPOSE OF LITHIUM POLYMER BATTERY WITH GENERAL WASTE. PLEASE DISPOSE OF IT IN A BATTERY RECYCLING COLLECTION POINT.

Speciﬁcations

EDGE® MOUNT

SIZE: 115X30X4.5 mm / 4.5X1.1X1.7 in
MATERIALS: CNC MACHINED ALUMINIUM, WITH N52 MAGNETS AND AN ULTRA GRIPPING LAYER ON THE FRONT SURFACE
WEIGHT: 34 gr / 1.1 oz

EDGE® UNIVERSAL WIRELESS CHARGER