LANCOM SYSTEMS LANCOM GS-3510XP Multi-Gigabit Ethernet Access Switch User Guide

LANCOM GS-3510XP
Hardware Quick Reference

LANCOM GS-3510XP Multi-Gigabit Ethernet Access Switch

1. Configuration interface (Console)
   Connect the configuration interface via the included serial configuration cable to the serial interface of the device you want to use for configuring/monitoring the switch.

2. TP Ethernet interfaces 10M/100M/1G
   Use Ethernet cables to connect interfaces 1 to 4 to further network devices.

3. TP Ethernet interfaces 100M/1G/2.5G
   Use Ethernet cables to connect the interfaces 5 to 8 to further network devices.

4. SFP+ interfaces 10G
   Insert suitable LANCOM SFP modules into the SFP+ interfaces 9 to 10. Choose cables that are compatible with the SFP+ modules and connect them as described in the SFP+ module’s documentation.

5. Power connector (device back side)
   Supply power to the device via the power connector. Please use the IEC power cable supplied or a country-specific LANCOM Power Cord.

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

Please observe the following when setting up the device
→The power plug of the device must be freely accessible.
→ For devices to be operated on the desktop, please attach the adhesive rubber footpads
→Do not rest any objects on top of the device
→Keep all ventilation slots on the side of the device clear of obstruction
→Mount the device into a 19” unit in a server cabinet using the provided screws and mounting brackets.
→Please note that support service for third-party accessories is excluded.

Mounting & connecting

➀ System / Link/Act/Speed / PoE

System: off| Device switched off
System: green| Device operational
System: red| Hardware error
Link/Act/Speed: green| Port LEDs show link/activity status or port speed
PoE: green| Port LEDs show PoE status
➁ Mode/Reset button
Short press| Port LED mode switch
~5 sec. pressed| Device restart
7~12 sec. pressed| Configuration reset and device restart
➂ TP Ethernet ports 10M/100M/1G
LEDs switched to Link/Act/Speed mode
Off| Port inactive or disabled
Green| Link 1 Gbps
Green, blinking| Data transfer, link 1 Gbps
Orange| Link < 1 Gbps
Orange, blinking| Data transfer, link < 1 Gbps
LEDs switched to PoE mode
Off| Port inactive or disabled
Green| Port enabled, power supply to
connected device
Orange| Hardware error
➃ TP Ethernet ports 100M/1G/2.5G
LEDs switched to Link/Act/Speed mode
Off| Port inactive or disabled
Orange| Link 100 Mbps
Orange, blinking| Data transfer, link 100 Mbps
Green| Link 1 Gbps / 2.5 Gbps
Green, blinking| Data transfer, link 1 Gbps / 2.5 Gbps
LEDs switched to PoE mode
Off| Port inactive or disabled
Green| Port enabled, power supply to connected
device
Orange| Hardware error
Orange blinked| PoE-Überlastung
➄ SFP+ ports 10G
LEDs switched to Link/Act/Speed mode
Off| Port inactive or disabled
Green| Link 1 Gbps
Green, blinking| Data transfer, link 1 Gbps
Blue| Link 10 Gbps
Blue, blinking| Data transfer, link 10 Gbps

Hardware

humidity 10–90%, non-condensing
Housing| Robust metal housing, 220 x 44 x 242 mm (W x H x D), network connectors on the front
Number of fans| Fanless

Interfaces
ETH
4 TP Ethernet ports 10 / 100 / 1000 Mbps
4 TP Ethernet ports 10 / 100 / 2500 Mbps
2 SFP+ ports 10 Gbps
10 concurrent Ethernet ports in total

Package Content

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance
with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of
Conformity is available at the following Internet address: www.lancom- systems.com/doc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>