somfy Situo 1 Variation RTS Single Channel Remote Control User Manual
- June 9, 2024
- somfy
Table of Contents
Variation RTS Single Channel Remote Control
User Manual
Situo 1 Variation RTS Single Channel Remote Control
EN The RTS Situo 1 Variation allows a group of one or more applications to be controlled, The RTS Situo 5 Variation allows up to 5 groups of one or more applications to be controlled.
Safety and liability
| 
---|---
| 
1. 1. Liability
These instructions must be kept by the user. Failure to follow these
instructions or use of the product outside its field of application is
forbidden, and will invalidate the warranty and discharge Somfy of all
liability.
This Somfy product must be installed by a professional motorisation and home
automation installer. Moreover, the installer must comply with the standards
and legislation currently in force in the country in which the product is
being installed, and inform his customers of the operating and maintenance
conditions for the product. Never begin installing without first checking the
compatibility of this product with the associated equipment and accessories.
If in doubt when installing this product and/or to obtain additional
information, contact a Somly adviser or go to the website www.somfy.com.
1. 2. Safety instructions
Do not use or install this product outdoors.
Keep the product out of reach of children.
Do not knock or drop the product, expose it to flammable materials or sources
of heat or moisture, or splash or immerse it.
2. The RTS Situo 1 Variation and the RTS Situo 5 Variation in detail
(Figure A)
a. Wall mounting recess
b.Up/On/Open button
c.ST0P/my button
d.Van1ator
e. Dow/Off/Close button
f.Key activation indicator light
g.Key activation and group selection indlights
h.Group selector
i.PROG button
j.Wall mounting.
Selecting the groups on the RTS Situo 5 Variation (FigureB)
Before using the RTS Situo 5 Variation, check that the correct group has been
selected.
Press repeatedly on the group selector @ to select the correct group.
The indicator light @ for each group from I to 4 is lit individually then all
the indicator lights are lit if group 5is selected.
Installation
4. 1. Adding/deleting an RTS Situo Variation
program the first control refer to the Instructions for the RTS motor or
recerver.
To add or delete the RIS Situo Variation to or from an application: (Figure C)
-
On the individual control already associated with the application:
• Press the PROG button (=2 s) until the application moves up and down, -
On the RIS Situo Variation to be added or deleted.
For the RIS Situo 5 Variation, first select the group.
Briefly press the PROG button: the application moves up and down and the RTS Situo Variation is added or deleted,
EN 4.2. Fastening (Figure D)
- Remove the protective film from the adhesive on the back of the wall mounting.
- Fasten the wall mounting to a flat, clean and dry surface. Press for optimum bonding.
- Place the RIS Situo Variation on the mounting.
Use
Before using the RIS Situo 5 Variation, check that the correct group has been
selected.
5. 1. Group selector on the RTS Situo 5 Variation
This allows the group to be displayed and changed (5 groups are available)
– Short press: visualisation of the group selected.
– Press several times: change of group.(f)
Group 5: all 4 indicator lights come on together.
5. 2. Buttons A/V (Figure E)
Depending on the type of application to be operated:
– A Up’0n/ 0pen
– V Down/Off/Close
5. 3. Variator (Figure F) Used to
– vary the angle of the adjustable slats on Venetian blinds
– vary the lighting and heating.
** Scroll 1 notch slats tilted 1 notch, lighting and heating changed per
variator notch, Scroll n notches: tilt the slats by n steps, vary the lighting
and heating by steps.
5.4, STOP button /my (Figure G)**
Briefly press my to stop the application from being activated.
If the application has been stopped, briefly pressmny to activate it until the
favourite position (my).
5.5, Setting, modifying or deleting the favourite position (my) (Figure H).
Place the application in the required position then press my (+ 5 s) to set
the favourite position (my).
Place the application in the favourite position (my) and press my (= 5 s) to
delete it.
Tips and recommendations
ToreplacethelastRTScontrolpointlostorbroken, contact a motorisation and
home automation professional.
Replacing the battery (Figure I)
Following the figure, remove the rear panel from the remote control, replace
the battery with a new one with the same characteristics then close the panel.
Risk of explosion if the battery is replaced byan incorrect type.
Keep new and used batteries away from Li children.
Do not ingest battery. If the battery is swallowed, it can cause chemical
burns in just 2 hours and can lead to death. If you think this occurred, call
a doctor immediately. If the battery compartment does not close securely, stop
using the product and keep it away from children.
Do not throw onto a fire as there is a risk of “I explosion.
Please separate storage cells and batteries from other types of waste and
recycle them via your local collection facility.
We care about our environment. Do not dispose of the appliance with usual
household waste. Give it to an approved collection point for recycling.
Technical data
Frequency range and maximum power used: 433.050 MHz – 434.790 MHz e.r.p. <10
mW Radio range: 20 m between two walls. Operating temperature: 0°C to +50°C
Power supply: 1 type CR2430 battery, 3 V.
SOMFY ACTIVITES SA hereby declares that the radio equipment covered by
these instructions is in compliance with the requirements of the Radio
Directive 2014/53/EU and the other essential requirements of the applicable
European directives. The full text of the EU Declaration of Conformity is
available at www.somfy.com/ce.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>