1871168 Somfy Connect BMS Interface V2 User Guide

1871168 Somfy Connect BMS Interface V2 User Guide

DESCRIPTION

The Somfy Connect™ BMS Interface V2 provides communication and control between Building Management Systems either as a stand-alone Somfy Digital Network™ (SDN) installation or when part of an animeo® IP system.

The interface communicates with the Building Management System through IP or serial connections to send and receive signals.

SYSTEM CONFIGURATION

All motors must be fully operational and programmed with limits prior to programming. Follow all installation guidelines and product documentation. A fully commissioned SDN or animeo IP system is required.

CONNECTIONS & INDICATORS

MOUNTING

The Somfy Connect™ BMS Interface V2 is mounted near the Building Management System, a network switch, or close to thebeginning of an SDN network.

This product features a DIN-rail mounting bracket on the back of the unit

SYSTEM SETUP

Stand-alone SDN connection to RS485 BMS system

• Connect the BMS Interface R1 port to an SDN device port
• Connect the BMS Interface R2 port to the RS485 BMS system Serial output

Stand-alone SDN connection to IP BMS system

• Connect the BMS Interface R1 port to an SDN device port
• Connect the BMS Interface Ethernet port to the Local Area Network Switch
• Connect the IP BMS System to the Local Area Network Switch

animeo IP connection to RS485 BMS system

• Connect the BMS Interface Ethernet port to the animeo IP Building Controller IP bus port
• Connect the BMS Interface R2 port to the RS485 BMS system Serial output

animeo IP connection to IP BMS system

•  Connect the BMS Interface Ethernet port to the Local Area Network Switch
• Connect the animeo IP Building Controller Network port to the Local Area Network Switch
• Connect the IP BMS System to the Local Area Network Switch

BIAS & TERMINATION DIP SWITCHES

All DIP switches should remain in an OFF position

CONNECT PC

The default IP address of the Somfy Connect™ BMS Interface V2 is 192.168.1.24 and subnet mask is 255.255.255.0. If the PC and interface are on different IP networks, temporarily assign a static IP address to the PC on the 192.168.1.x network. If the address has been changed to an unknown IP address, use the Somfy Connect FieldServer Toolbox software to identify the device.

1. CONNECT a Cat-5 Ethernet cable between the Somfy Connect BMS Interface V2 Ethernet port and a Windows PC Ethernet port

2. In Windows PC, NAVIGATE to network connections

3. SELECT the network device connected to the Somfy Connect BMS Interface V2

4. SELECT “Change settings of this connection”

5. In the Ethernet properties window networking tab, SELECT “Internet Protocol Version 4 (TCP/IPv4),” then SELECT “Properties”

6. In the Internet Protocol Version 4 (TCP/IPv4) Properties

   • SELECT the “Use the following IP address:” radio button

   • ENTER the IP address: 192.168.1.x (x can be from 2 to 255 except for 24)
     ENTER the subnet mask: 255.255.255.0

   • SELECT “OK” on both windows to apply settings

7. OPEN a web browser to NAVIGATE and LOGIN to the Somfy Connect BMS Interface V2 http://192.168.1.24

8. Refer to the Somfy Connect BMS Interface V2 Programming Guide for additional support

Upon completion of the Somfy Connect BMS Interface V2 configuration,  repeat Step 6 to revert previous settings.In the Internet Protocol Version 4 (TCP/IPv4) Properties, SELECT the “Obtain an IP address automatically” radio button

RESOURCES & APPLICATIONS

For the latest resources go to:
https://www.somfypro.com/products/-/ecat//1871168

• Somfy Connect BMS Interface V2 for SDN and animeo IP Programming Guide
• Somfy Connect BMS Data Points Deployment Guide
• Somfy Connect FieldServer Toolbox to discover assigned IP addresses

References

• Products - us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>