RAB MW-S-SMW-S Microwave Smart Sensor Instructions
- June 2, 2024
- RAB
Table of Contents
MW-S-SMW-S Microwave Smart Sensor
Instruction Manual
RAB Lighting is committed to creating high-quality, affordable, well-
designed and energy-efficient LED lighting and controls that make it easy for
electricians to install and end users to save energy. We’d love to hear your
comments. Please call the Marketing Department at 888-RAB-1000 or email:
marketing@rablighting.com
HID-XXX-V-EX39-XXX-BYP-HB-ECO Our sensor product numbers include MW-S/SMW-S,
PIR-S/SPIR-S and DAYLIGHT-S are optional accessories for select High Bay
lamps. The lamps will perform as normal if no sensor is inserted. Please note
that RAB lamps can’t operate with other brand sensors.
MW-S-SMW-S Microwave Smart Sensor
IMPORTANT
READ CAREFULLY BEFORE INSTALLING LED HID BULBS. RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
RAB ED HID Bulbs must be wired in accordance with the National Electrical Code
and all applicable codes. Proper grounding is required for safety THIS PRODUCT
MUST BF INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTAL ATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THF PRODUCT AND THE
HAZARDS INVOIVFD
WARNINGS:
-
Main applications include for use in high bay and other suitable light fixtures.
-
Operating temperature: -30°( to 60°( (-22°F to 140°F).
-
These LED Lamps require all ballasts, capacitors, and ignitors to be bypassed or removed. Do not operate lamps on existing ballasts.
-
Dimmable with optional control modules.
-
Do not use with standard dimmers. Only use the control provided with or specified by these instructions to control this lamp.
This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control. -
This device is not intended for use with emergency exits.
-
For use in enclosed fixtures.
-
Before installation make certain the AC power to the fixture is off.
-
Risk of fire or electric shock. LED Retrofit lamp installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
-
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
-
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
-
Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
-
WARNING- RISK OF FIRE OR ELECTRIC SHOCK, INSTALLATION OF THIS RETROFIT KIT REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE LUMINAIRE’S ELECTRICAL SYSTEM AND THE HAZARD INVOLVED, IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION, CONTACT A QUALIFIED ELECTRICIAN.
-
THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIREWHERETHE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION, PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES, THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS,
INSTALLATION INSTRUCTION
Burning positions: base up
You must use the safety cable to secure the lamps in case of falling down due
to old socket Attach one end of the safety cable to the lamp and the other end
to the luminaire
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
LAMP INSTALLATION
Step:1 Turn off the power before installation. As shown in Figure 1 Remove the old Ballast, Capacitor and Ignitor (if existing).
Step:2 As shown in Figure 2 Make sure the Alternating Current Wires
connect to the socket directly. (Reattach or replace ground lead if one is
needed).
Step:3 As shown in Figure 3 Screw the LED lamp into the corresponding
socket. Attach retrofit label to luminaire.
Securely fasten the ground wire to the main body structure. If the wire is damaged in any way please replace (Do not use existing burnt out wire). If needed, the replacement ground wire must be 1.0mm in size and insulated from heat.
© 2023 RAB LIGHTING Inc.
Cranbury, New Jersey 08512USA
COHB-IN-0123
rablighting.com Visit our website for product info
Tech Help Line Call our experts: 888 722-1000
e-mall Answered promptly –
sales@rablighting.com
Free Lighting Layouts Answered online or by request
RAB WARRANTY: RAB’s warranty is subject to all terms and conditions found at
rabfighting.com/warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>