RAB Lighting Inc DSK34-4R129XX120WS Disk Downlight Instructions

RAB Lighting Inc DSK34-4R129XX120WS Disk Downlight

Product Information

The DISK34-4 DISK is a downlight luminaire that has been modified to operate LED lamps. It is not compatible with incandescent lamps. The luminaire comes with a disk, bracket, screws, nuts, Lumi sticker, and optional accessories like E26 adapter, female connector, and friction clips. It is compatible with most common 4 recessed housings, and the LAMPSOCKET E26 SET Model# DSK34-4/ACC is needed for installation.

Important Safety Instructions

• Power should be turned off at the fuse box before installation.
• Read all product labels and directions.

What’s in the Box

• Disk (1)
• Bracket(1)
• Screws (4)
• Nuts (3)
• Lumi Sticker (1)

Optional Accessories
Our disk downlight is compatible with most common 4” recessed housings, please purchase the LAMPSOCKET E26 SET (Model# DSK34-4/ACC – including E26 adapter, female connector and friction clips) for installation in housings.

• E26 adapter(1)
• Female connector(1)
• Screw (2)
• Friction Clips(2)

Tools Needed

A screwdriver is needed for installation.

Dimensional Drawings

Minimum lamp compartment dimensions for installation with J-BOXJ-box Min Volume – 15.9 in3, Min Length: 3.2in, Height: 1.55in Compatible with standard J-box. Minimum lamp compartment dimensions for installation with Existing Housing: Dia: 4in, Height: 4.1in Compatible with most common 4in recessed housings

Product Usage Instructions

Installation with J-BOX (Mounting Diameter 2.7in) using Bracket

J-box Min Volume – 15.9 in3, Min Length: 3.2in, Height: 1.55in Compatible with standard J-box

1. Take out the lens from the disk. (Fig.1)
2. Fasten the bracket to J-box with the two long screws provided in the package. (Fig.2)
3. Connect the ground wire (Cooper) to the J-box and the wires of the J-box to the disk, white-white, black-black. (Fig.3)
4. Fasten the disk to the bracket with the two short screws provided in the package. (Fig.4)
5. Put the lens back into the disk.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXT\JRE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixture must be wired in accordance with the National Electrical Code and all applicant-able local codes. Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITI-HHE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH 1HE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. TO PREVENT ELECTRICAL SHOCK, POWER SHOULD BE TURNED OFF AT THE FUSE BOX BEFORE INSTALLATION

SAFETY WARNINGS
Read all product labels and directions.

WARNING:  Risk of fire or electric shock. LED Retrofit Kit Installation requires knowledge of luminaires’ electrical systems. If not qualified, do not attempt Installation. Contact a qualified electrician

• THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.
• WARNING Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• WARNING   To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
• Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
• Replace only with RAB Lighting Inc. Visit our website: RABLIGHTING.COM Call our experts at 888 722-1000 MODEL# DSK34-4R129XX120WS/DSK34-4R129XX120BS/DSK34-4R129XX120BRS/DSK34-4R129XX120BNS/DSK34-4R149XX120WS.
• The recessed luminaire is intended for mounting only in a covered ceiling where only the led side of the luminaire will be exposed to damp or dry locations.
• INSTALLATION SHOULD ONLY BE PERFORMED AFTER THE POWER TO THE FIXTURE HAS BEEN DISCONNECTED.
• These instructions shall be included on an information sheet packaged with each unit.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

INSTALLATION WITH J-BOX (Mounting Diameter ＞2.7in)

1.  Make sure the POWER IS TURNED OFF at the source to the J-box in which you are installing the product.

2.  Take out the lens from the disk. (Fig.5)

3.  Fasten the bracket to J-box with the two long screws provided in the package. (Fig.6)
   

4.  Connect the Ground Wire (Cooper) to the J-box and the wires of J- the box to the disk, white-white, black-black. (Fig.7)

5.  Fasten the disk to the bracket with the two short screws provided in the package. (Fig.8)
   

6.  Put the lens back on the disk. (Fig.9)

INSTALLATION WITH EXISTING HOUSING

1.  Wire the disk with a female connector. (Fig.10) Insert the black wire into the side marked(-) and the white wire into the side without mark. Make sure both wires are tightly secured.

2.  Make sure the POWER IS TURNED OFF at the source of the recessed housing in which you are installing the product.

3.  Take out the lens from the disk. (Fig.11)

4.  Fasten the bracket to the disk with the two short screws provided in the package. (Fig.12) Pay attention to the direction of the bracket.

5.  Install the friction clip on the back of the disk. (Fig.13) Put the lens back to the disk. (Fig.14)
   

6. Screw the E26 adapter into the socket. Then connect the male connector of the E26 adapter to the female connector of the disk. (Fig.15) Simply slide the trim and metal friction clips into the housing. (Fig. 16) Carefully place wires into fixture and push the LED trim into the housing until flush with ceilings (Fig.17)

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation, or maintenance

References

• Welcome to RAB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>