GOAL ZERO 800 Watts Nomad 400 PRO Solar Panel Bundle User Guide

June 15, 2024
GOAL ZERO

GOAL ZERO - logo

NOMAD 400
SOLAR PANEL
USER GUIDE

DISCLAIMER
Please read all warnings, instructions and cautions carefully before use to avoid personal injury, property damage or damage to your Goal Zero product. Goal Zero reserves the right to update this document without prior notice. Please visit www.goalzero.com to find the latest product information and the most recent version of the User Guide.
For assistance with your device in the United States, visit our contact page at www.goalzero.com/contact or call 1-888-794-6250. For assistance with your device outside of the United States, contact the local distributor. If you do not have contact information for the local distributor, contact us in the United States and we will help connect you to the local representative.

Get to Know Your Gear

GOAL ZERO 800 Watts Nomad 400 PRO Solar Panel Bundle -

In the Box

  • Nomad 400 solar panel
  • 15 ft HPP extension cable

Connecting Your Solar Panel

  1.  Unfold your panel and the kickstands. Then angle your panel toward the sun.
  2.  Plug the HPP connector into the input port on your Goal Zero power station, or plug a small electronic device directly into the USB-A connector.

For the best solar charging experience, reposition the solar panel throughout the day. Before connecting your Nomad 400 into any device, be sure to reference the device specifications to ensure compatibility.

GOAL ZERO 800 Watts Nomad 400 PRO Solar Panel Bundle - Solar
Panel

Connecting Multiple Panels

When connecting multiple panels, it is important to be mindful of the voltage input limitations of the device you are charging.
The amount of input is impacted by whether you are connecting panels in a series or parallel configuration. Visit the Goal Zero website for more information about optimum solar panel setup:

GOAL ZERO 800 Watts Nomad 400 PRO Solar Panel Bundle - qr
codehttps://qrco.de/be4sU5

Technical Specifications

Solar Panel

Rated Power* 400W±3%
Cell Type Monocrystalline
Cell Efficiency 23%
Operating Voltage (peak power) 20.66V
Operating Current (peak power) 19.38A
Open Circuit Voltage VOC 23.84V
Short Circuit Current ISC 20.45A
Temperature Coefficient (voltage) -0.36%/K
Operating Temperature -40° to 185°F
Ingress Protection IP65

Connection
Connector 1| HPP; 6 inches/15.24 centimeters; 12AWG
Connector 2| USB; 6.5 inches/16.51 centimeters
General
Weight| 36.6 pounds (16.6KG)
Dimensions (unfolded)| 114 x 31.6 x 0.19 inches 2895 x 805 x 5 mm
Dimensions (folded)| 28.54 x 31.6 x 1.18 inches 725 x 805 x 30 mm
Certs|
Warranty| 2 years

You can charge a Yeti PRO 4000 with two Nomad 400 panels in one day of full sun
*For warranty terms, conditions, and registration, go to www.goalzero.com/warranty.

  • Based on Standard Test Conditions with Solar irradiance at 1000W/m^2, cell temperature of 25C and air Mass AM = 1.5

GOAL ZERO HEADQUARTERS
Draper, UT 84020
1-888-794-6250
Designed in the U.S.A.
Made in China
Goal Zero Yeti is a trademark of Goal Zero.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SM052423
GOALZERO.COM

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals