LNC ZQQEUALWS87W398 Exalted 21.6-in 3-Light Polished Gold and Smoky Grey Glass LED Instruction Manual

June 3, 2024
LNC

LNC ZQQEUALWS87W398 Exalted 21.6-in 3-Light Polished Gold and Smoky Grey Glass LED Instruction Manual

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.

  2. Please read the instruction carefully and save it as you may need it at a later time.

  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

    • Go to the main fuse, or circuit breaker, box in your home.
      Place the main power switch in the “OFF” position.

    • Place the wall switch in the “OFF” position.

  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

  6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.

  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

TOOLS REQUIRED

PARTS INCLUDING

(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Back plate (1)
(F) Stud (2)
(G) Glass shade-A (6)
(H) Screw (24)
(I) Glass shade-B (6)
(J) Bracket (3)
(K) Arm (3)
(L) Tube (3)

PARTS INCLUDING

ACCESSORIES ENCLOSED

(A) Mounting screw (2)
(B) Plastic wire connector (3)
(H) Screw (1) (spare part)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done
    Go to the main fuse, or circuit breaker, box in your home.
    Place the main power switch in the “OFF” position.
    Place the wall switch in the “OFF” position

  3. Make assembly
    ASSEMBLY & INSTALLATION INSTRUCTIONS

Step A1

  1. Unscrew studs (F) from back plate (E) and mounting plate (C), then set them aside for later installation.
  2. Screw tubes (L) to arms (K) as shown in the illustration.

Step A2
Carefully pass the supply wires from the outlet box through mounting plate (C).
Secure mounting plate (C) to the outlet box with mounting screws (A).

Step A3
Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect ground wires according

Connect wires according to the below chart

Connect Black or Red Supply Wire to: Connect White Supply Wire to:
Black White
Parallel cord (round & smooth) Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer Clear, Brown, Gold or Black with

tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step A4  Align the holes in back plate (E) and mounting plate (C), then secure them with the previously removed studs (F).

Step A5

  1. Remove screws (H) from brackets (J).
  2. Attach glass shades-B (I) to the opposite sides of brackets (J) with screws (H) as shown in the illustration.
  3. Insert glass shades-A (G) into the grooves of glass shades-B (I) as shown in the illustration.
  4. Thread screws (H) to holes of brackets (J) to secure glass shades-A (G) as shown in the illustration.
  5. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals