PNi HS003 SafeHouse Motion sensor User Manual
- June 3, 2024
- PNI
Table of Contents
PNi HS003 SafeHouse Motion sensor User Manual
PRODUCT INFORMATION
The PIR sensor PNI HS003 adopts a digital infrared control system and an intelligent analysis algorithm. This allows it to recognize the interference signals and the human movement signals to avoid false alarm. The device has the features of environmental-friendly, safety, and easy installation. The sensor sends a low voltage alarm to the alarm system, then the alarm system will send a low voltage message to the users (if capable). PNI HS003 is compatible with PNI SafeHouse HS650, PNI SafeHouse HS60, PNI SafeHouse PT700, PNI PG2710 wireless alarm systems.
MAIN FUNCTION PARAMETERS
- It adopts a microprocessor for low-power consumption, thus the battery will have a longer life
- It transfers digital wireless signals
- Low voltage alert function
- Automatic temperature compensation
- Intelligent analysis to avoid fault alarm
- Protection against the white light
- Protection against high-frequency interference
PRODUCT DESCRIPTION
| No. | Description | No. | Description |
|---|---|---|---|
| 1 | Detection window | 6 | Antenna |
| 2 | LED indicator | 7 | LED indicator |
| 3 | Installation bracket | 8 | Infrared sensor |
| 4 | AAA 1,5V battery | 9 | Operating mode (J4) |
| 5 | Data settings (J2) | 10 | Led setting (J3) |
LED INDICATOR LIGHT
LED flashes frequently: device is in self-checking state
LED flashes once: device is in alarming state
LED flashes twice: device finishes self-checking and enters working mode.
LED flashes three times : battery under-voltage (you will receive a low
voltage alert if your GSM alarm system is connected to the PIR sensor)
PCB LAYOUT
Infrared sensor: it detects the infrared radiation emitted by the heat of
the human body. Please don’t touch the lens with your hand and keep it clean.
Data setting (J2): Setting appropriate data bits according to the alarm
panel with user’s requirement. (default is insert) Do not modify unless
neccesary.
LED setting (J3), To enhance the elusive of the detector to disable LED
(default is insert)
Mode choosing (J4): Insert J4 to be in test mode, without J4 sensor is in
sleeping mode.
USE INSTRUCTIONS
Toggle switch to the ON position, the detector releases 2s wireless signal
immediately, then enter selfchecking, and then enter working mode 30s later;
In working mode, can choose the corresponding detection mode by Jumper J4.
Factory default mode: test mode
- Test mode: The sensor detects once every 2.5s. It will send an alarm signal when it detects the infrared signals from human body. Check the installation height and adjust the angle of the sensor.
- Sleeping mode: If the detector constantly detects 4 times alerts within 3 minutes, it will enter sleeping state to save battery power. It will activate itself after waiting for 3 minutes when there’s no alert.
Coding operation
Set the alarm panel in coding state. After installing the battery, the detector will send a wireless signal to the alarm panel. Move your hand in front of the detector to trigger an alarm, then the detector will send the wireless signal to alarm panel
PRODUCT INSTALLATION
To ensure a normal operation, the detector must be away from enrironments with frequent temperature changes and air flows. Please don’t put your detector near window, air conditioner, fluorescent lamp, heating devices, fridges, oven, stove, sunshine, etc. Also do not install 2 detectors in the same zone to avoid interference and fault alarms.
PRODUCT TESTING
After installation of the battery, the device will self-check 30 seconds and
then go to test mode, please walk around in the detection zone from left to
right or right to left, observing the LED’s flashes, and make sure the device
is detecting movement and working normally. The LED indicator flashes once
when it detects the movement of human body.
Adjust the height and the angle of the device to get the best detection range
DETECTION RANGE DIAGRAM
TECHNICAL PARAMETERS
Operating voltage: 3V/2xAAA alkaline bateries| Detection range: 8m ~ 12m
(25°C)
---|---
Working current: ≤ 25mA| Working temperature: -26°C ~ +80°C
Standby current: ≤ 15mA| Installation method: Wall mounted
Communication frequency: 433 Mhz| Installation height: 1.8 ~ 2.2m
Transmission power: 10 mW| Detection angle: 110°
Communication distance: ≥80m (in open area)| Dimensions: 1054026mm
TROUBLESHOOTING
| Failure | Solution |
|---|---|
| LED failed | Check battery installed well or not |
Check the power of battery run out or not
Check jumper J3 whether inserted or not
LED flashes 3 times periodically| Low voltage, please replace the battery
Emission distance gets shorter| The battery is running out
No response for detecting| Jumper cap J4 to be sleeping mode or not
EU Simplified Declaration of Conformity
SC ONLINESHOP SRL declares that Movement sensor PIR PNI SafeHouse HS003
complies with the Directive EMC 2014/30/EU and RED 2014/53/UE. The full text
of the EU declaration of conformity is available at the following Internet
address:
https://www.mypni.eu/products/6473/download/certifications
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>