PNI B6500 Audio Baby Monitor User Manual
- May 15, 2024
- PNI
Table of Contents
PNI B6500 Audio Baby Monitor
Specifications
- Power supply: 5V (via Micro-USB port), 3.6V (3 x AAA 1.2V NiMH batteries)
- Communication frequency: 2.4GHz
- Emission power: Not specified
- Communication distance: Not specified
- Microphone: Included
- Speaker: Included
- Dimensions: Not specified
- Working temperature: Not specified
Product Usage Instructions
Baby Unit
The baby unit of the PNI B6500 Audio Baby Monitor includes various
features:
- A – L ED indicator
- B – On/off button (long press to operate)
- C – Night light
- D – Microphone
Power Supply
- The baby unit is powered by 3 AAA Ni-MH rechargeable batteries.
- To charge the batteries, use the provided power cable and connect it to a MicroUSB port on the unit.
Parent Unit
The parent unit of the PNI B6500 Audio Baby Monitor includes several
functions:
- E – LED indicator
- F – PTT button (press and hold to talk to the child remotely)
- G – Control night light on/off on the child unit
- H – Volume control
- I – On/off button (long press to operate)
- J – Microphone
Power Supply
The parent unit also uses 3 AAA Ni-MH rechargeable batteries. Follow the
same charging procedure as the baby unit.
Pairing the Two Units
If the units lose communication, press and hold the on/off button on both
units simultaneously for about 5 seconds to pair them again.
Safety warnings
PNI B6500 is a safe-to-use product that meets the relevant standards related to electromagnetic fields.
- Before using this product, read the instruction manual carefully.
- The product should only be assembled by adults.
- Do not allow children access to the power cords.
- This product is not a toy. Do not allow children to play with it.
- This product does not replace the responsible supervision of an adult.
- Position the product at least 1 meter away from the child.
- Do not keep the product close to heat or water.
- Observe the supply voltage recommended by the manufacturer.
Baby unit
- A – LED indicator
- B – On /off button (long press the button to turn the unit on /off)
- C – Night light
- D – Microphone
Power supply
The baby unit includes 3 AAA Ni-MH rechargeable batteries of 1.2V 800mAh. To charge the batteries, insert one end of the power cable (included) into the Micro-USB port on the back of the unit and the other end into a 230V USB adapter (not included). Also, the unit can be powered with alkaline batteries (not included). Warning: Do not charge alkaline batteries!
Parent unit
- E – LED indicator
- F – PTT button (press and hold to talk to the child remotely)
- G – Turn the night light on /off on the child unit
- H – Volume control
- I – On /off button (long press the button to turn the unit on /off)
- J – Microphone
Power supply
The parent unit includes 3 AAA Ni-MH rechargeable batteries of 1.2V 800mAh. To charge the batteries, insert one end of the power cable (included) into the Micro-USB port on the back of the unit and the other end into a 230V USB adapter (not included). Also, the unit can be powered with alkaline batteries (not included). Warning: Do not charge alkaline batteries!
Pairing the two units
Note: the two units are paired from the factory.
If a problem occurs and the two units no longer communicate even though they
are within the recommended range, follow the procedure below to pair them
again: Press and hold the on /off button on both units simultaneously for
about 5 seconds.
Out of range
When the two units are too far from each other, an alarm is triggered: the
parent unit will emit a continuous beep, and the LED on both units will flash
red /green.
Discharged battery
When the batteries installed in any of the units are discharged, the unit will
beep every 30 seconds and the LED will flash red.
Pager (unit location)
Briefly press the on /off button on the child unit to send a signal to the
parent unit to locate it. The parent unit will output a Di .., Di .., Di ..
sound until you briefly press the on /off button.
Night light
You can turn the night light on or off by 3 methods:
- Briefly press the power button on the parent unit once.
- Briefly press the side button (C-night light) on the parent unit.
- Briefly press the on /off button on the child unit 3 times.
As long as there are noises in the child’s room, the child unit will emit continuously. Approximately 30 seconds after the interruption of any noise, the unit will enter standby mode (no longer emits). When the unit detects noise again, it starts emitting. The time when it starts emitting depends on the set sensitivity.
Microphone sensitivity control
K – Microphone sensitivity adjustment (Hi/Lo)
- Move the knob to the right to activate the low sensitivity of the microphone, a setting suitable for noisy environments or when the child unit is close to the child. The child unit starts emitting when the sound reaches 60 dB.
- Move the knob to the left to activate the high sensitivity of the microphone, setting suitable for quiet environments or when the child unit is further away from the child. The child unit starts emitting when the sound reaches 50.
Note: Position the child unit 1 – 3 meters away from the child.
Technical specifications
Power supply| 5V (via Micro-USB port) 3.6V (3 x AAA 1.2V Ni-
MH batteries)
---|---
Communication frequency| 2.4GHz
Emission power| 100mW
Communication distance| Up to 100 meters (in open field)
Microphone| Built-in
Speaker| Built-in
Dimensions| 70 x 40 x 100mm
Working temperature| -26°C ~ +80°C
Simplified EU declaration of conformity
SC ONLINESHOP SRL declares that Audio Baby Monitor PNI B6500 is under the EMC
Directive 2014/30/EU and the RED Directive 2014/53 /EU. The full text of the
EU Declaration of Conformity is available at the following website:
https://www.mypni.eu/products/9124/download/certifications
FAQ
- Q: How do I know if the units are out of range?
- A: When the units are too far from each other, an alarm is triggered with continuous beeping and flashing red/green LEDs on both units.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>