PNI IP590 Wireless Video Surveillance Camera User Manual
- June 1, 2024
- PNI
Table of Contents
PNI IP590
Wireless video surveillance camera
Safety warnings
- Change the camera password immediately after the first connection.
- If you are in an environment with high dust and humidity, do not open the protective cover to insert a micro SD card into the camera.
- In case of failure, contact a specialized service center, do not open the camera housing.
Product introduction
- Microphone
- Lens
- WiFi antenna
- Power supply
- Ethernet
- Protective cover
- Loudspeaker
- Micros SD card slot
- Reset button
Technical specifications
| Sensor | 2 x 2.0MP, 1/2.8″ CMOS |
|---|---|
| Minimal lighting | Day: 0.01 Lux @(F1.2, AGC ON) Night: 0.001 Lux @ (F1.2, AGC |
ON), 0 Lux cu IR
Shutter| 1/50 (1/60) sec. – 1/10000 sec.
Lens| 4mm@F1.6
IR-Cut filter| Yes
Video compression| H. 265A1/H.265+
Audio compression| G.711A
Image resolution| 3840 x 1080px@l2fps
Wireless standard| WiFi 802.11 b/g/n
WiFi frequency| 2.4GHz
WiFi transmission power| 100mW
Ethernet| 1 x RJ45
Power voltage| 12 V DC
LED| 4 x IR and White LEDs
IR distance| up to 40 m
Protection grade| 1P66
SD card slot| Yes, up to 128Gb
Visibility angle| 180°
Dimensions| 203 x 107 x 63 mm
Operating temperature| -26°C — +80°C
Camera configuration. ICSee app.
Warnings:
- Configure the camera before installing it in the final location.
- Add a micro SD card to the camera and power the camera before adding it to the app.
- The camera only supports 2.4GHz WiFi connection.
- Due to the numerous updates of the ICSee application, it is possible that the images and information described in this manual are different from the version you have installed.
- Search for the ICSee application in the App Store or Google Play or scan the attached QR code:
- Install the application, create an account and log in.
- Connect your phone to the WiFi network and activate Location.
- Press the “+” button to add the camera to the application.
- In the following interface, click on “WiFi Camera”.
- Power on the camera. You will hear the voice prompt: “System starting up” then “Wait to be configured”.
- In the application, press “Next”.
- Select the WiFi network you want to connect to and enter the network’s password.
- Press “Confirm”.
- Position the QR code from the application in front of the camera lens.
- After the camera has been added, set a password and name the camera.
- Select the recording mode: continue, only with motion detection or in the Cloud (for a fee).
- Press “Done” to complete the procedure of adding the camera to the application.
Frequently asked questions
Where does the camera save video recordings?
The video recordings are saved on the micro SD card (max. 128Gb) installed in the camera. The micro SD card is purchased separately. Also, recordings can be saved in the Cloud (paid service).
How do I proceed if I forgot the camera password?
If you forgot the password, reset the camera by pressing the Reset button next to the micro SD card slot and adding it again to the application.
How do I proceed if the camera status is Offline?
1. First check the power supply of the surveillance camera. 2. Turn off the power and power the camera again. 3. Reset the camera by pressing the Reset button located next to the micro SD card slot.
EU Simplified Declaration of Conformity
SC ONLINESHOP SRL declares that Video surveillance camera PNI IP590 complies
with the Directive EMC 2014/30/EU and RED 2014/53/UE.
The full text of the EU declaration of conformity is available at the
following Internet address:
https://www.mypni.eu/products/9115/download/certifications
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>