PowerPac PPV3100 Smart Robotic Vacuum Cleaner with Remote Control User Manual

SMART ROBOTIC VACUUM CLEANER WITH REMOTE CONTROL
PPV3100

Parts & Description

Start / Pause button

How to Operate the Remote Control

Note:

• Please install two pieces of AAA batteries for the Remote Control.
• If the Remote Control is not going to be used for a long period of time, please remove the batteries from the Remote Control.

| Button| Standby mode| Operating mode
---|---|---|---
1.| Start/Pause| appliance starts vacuuming according to the Auto mode| appliance stops vacuuming and enters the Standby mode
Under the Sleep mode, appliance enters the Standby mode
Under the Standby mode, appliance enters the Operating mode
Under the Operating mode, appliance enters the Standby mode
2.| Up
Down
**** Left
► Right| appliance moves forward
appliance rotates 180° and then moves forward appliance rotates 90° to the left and then moves forward appliance rotates 90° to the right and then moves forward| appliance moves forward appliance rotates 180° and then moves forward appliance rotates 90° to the left and then moves forward appliance rotates 90° to the right and then moves forward
3.| AUTO| appliance starts vacuuming
according to the AUTO mode| appliance starts vacuuming according to the AUTO mode
4.| focus| appliance starts vacuuming
according to the focus mode| appliance starts vacuuming according to the focus mode
5.| edge| appliance starts vacuuming
according to the edge mode| appliance starts vacuuming according to the edge mode
6.| return| appliance returns to the Charging Dock for charging| appliance retums to the Charging Dock for charging

Warnings

ATTENTION :
Read this booklet carefully as it contains important instructions for a safe installation, use and maintenance.
Important instructions to be kept for future reference.
The following basic precautions should always be followed when using electrical appliances:

1. Read all instructions before using the appliance.

2. This appliance must be used only for the purpose it was expressly designed; any use NOT complying with the instructions contained in the manual is considered inappropriate and dangerous. The manufacturer is NOT responsible for possible damages caused by the inappropriate and/or unreasonable use.

3. This appliance is NOT suitable to be used or stored near heat sources (open flame, ovens, heaters, stoves, etc.) and/or in an explosive environment (in the presence of flammable substances such as gas, vapour, mist or dust, in atmospheric conditions when, after ignition, the combustion is spread in the air). Items containing these substances should never be placed in the appliance, and never be used to clean the appliance in order to avert the risk of fire or explosion.

4. This appliance must NOT be used for vacuuming burning, smoking, toxic, volatile or flammable substances. The appliance must NOT be used to clear sewers. An explosion may occur if the appliance suctions sewer gases. Sewer gases inhalation may lead to unconsciousness and death.

5. It is NOT recommended to use the appliance for cleaning open stoves or other devices that contains oil or grease, soot, clay dust, plaster or other similar materials that are resistant to water action.

6. DO NOT vacuum mud, gypsum material, wall powder, blade, kindling, clumps of hair, large pieces of paper and other items such as sharp metal objects as that may make the air inlet or outlet, brushes & strainers get blocked and the motor gets burned. An indication of blockage may manifest as an abnormal sound or poor suction. If these small particles were absorbed, please disconnect the power cord and remove them from the Dustbin, air inlet or outlet, brushes & strainers immediately.

7. The packing materials (plastic bags, expanded polystyrene, etc.) must be kept out of the reach of children or disabled persons since they represent potential sources of
   danger.

8. Avoid carrying out operations which are NOT specified in this manual (such as disassembling, repairing and/or altering) by yourself, otherwise it will damage the appliance and cause injury to persons/animals or damage objects, for which the manufacturer cannot be considered responsible. The installation/assembly of the appliance will be  made in accordance with the indications of the manufacturer.

9. Place and use the appliance on a horizontal, stable and heat-resistant surface.

10. Before use, check the integrity of the appliance and power adapter (consisting of the adapter, plug and cable). In case you are not sure, contact a qualified person. If the
    power adapter is damaged, it must be replaced by the manufacturer or its service agent or a qualified technician in order to avoid a shock hazard.

11. Before charging the appliance make sure the rating (voltage and frequency) corresponding to the grid and the socket is suitable for the plug of the appliance, and that the wall socket is properly grounded.

12. DO NOT power the appliance using multiple sockets. If possible, avoid the use of adapters and/or extension cables; if their use is absolutely necessary, use only materials in compliance with the current safety regulations and according to the electrical parameters of the adapters.

13. The appliance must NOT be switched on using external timers and/or other remote control appliances which are not specified in this manual.

14. Only use original components & accessories (e.g. power adapter, remote control, lithium battery, dustbin) provided by the manufacturer. Any non-original components &
    accessories NOT recommended by the manufacturer may cause injuries to persons or damage to the appliance.

15. If you are using the appliance for the first time, you should:
    a. Charge the appliance for more than 12 continuous hours;
    b. Before using this appliance, please remove all items situated on the floor which may topple, break or spill their contents (e.g. cups, vases, ornaments, etc. made of glass, ceramic) on the floor and those that may entangle the side brush and air suction channel (e.g. electric wire, paper scraps, small pieces of cloth, etc.). Use the appliance only if the Dustbin, Preliminary strainer & Efficient strainer are installed! This is especially so if the surroundings to be vacuumed is extremely dusty. Failure to do so will only send the dust back out after being suctioned. DO NOT use other filters/strainers except the ones attached to the appliance by the manufacturer.
    c. Use the appliance only if the motor is in a good working condition before turning on this appliance. Failure to do this could cause a risk of injury to persons and would defeat the utility of the appliance.
    d. When the appliance is in operation, please pay attention to the presence of babies, children, the elderly and infirm, and animals to avoid a person or animal being hit, tripping or falling inadvertently when the appliances makes contact with them. Please do not touch wheels and side brushes by hand, so as to avoid injury.
    e. Switch the appliance OFF by pressing the “Start/Pause” button on the Remote Control or the button on the appliance and unplugging the power adapter from the electric mains when not in use and before emptying, cleaning and storing the appliance.
    f. Should there be a need to stop the appliance from operating, simply press the “Start/Pause” buttonon the Remote Control or the button on the appliance. Make sure to remove any label or protective sheet which may prevent its proper functioning.
    DO NOT:
    • charge the appliance before making sure power supply switch at the bottom of the appliance is turned OFF;
    • cover the appliance during functioning;
    • obstruct totally nor partially the air inlet or outlet with anything that may reduce the suction, such as dust, lint, hair, etc.;
    • allow the appliance to enter and operate on wet surfaces, e.g. in a wet kitchen, bathroom, locker room, etc.;
    • allow toddlers or small children to stand or sit on the appliance, especially when it is in operation. Although this advice may seem ridiculous to adults, however young
    children usually view situations differently, and may view riding on a moving appliance to be particularly appealing;
    • allow the appliance to vacuum stairs as the appliance may fall and gets damaged, cause damages to other objects, or cause injuries to people and animals;
    • insert objects or body parts inside the protection cover of the appliance;
    • touch the battery contacts with metal and conductive materials, otherwise it may cause a short circuit, resulting in heat, fire or explosion;
    • use the appliance for more than 60 minutes without turning it off for at least 15 minutes for a total usage of 2 hours in a single day – failure to heed this warning may result in motor failure;
    • leave the appliance unsupervised during operation.

16. Before unplugging the appliance, switch off the electric mains. Plug and unplug the power adapter holding it firmly with dry hands. Always unplug the power adapter to avoid overheating and avoid stretching it. DO NOT pull it, tug it or use it to drag the appliance to which is connected.

17. DO NOT use the power adapter as a handle, pull or carry the appliance by the power adapter cable, pull the cable around sharp edges, abrasive surfaces or corners,  run the appliance over the cable or close a door on the cable. Keep the cable away from heated surfaces, abrasive or sharp surfaces or in positions where it can be  damaged easily. Do not clean the product during charging

18. During operation, DO NOT touch the appliance with wet body parts, and it is recommended to have between you and the standing surface, an isolating element (for
    example, wearing shoes with rubber soles).

19. DO NOT use the appliance to clean up liquids outdoors, upon an earth floor. If it should be necessary to step on a wet or damp floor to pick up water, DO NOT touch the metallic parts of any electric device, lamp or switch while performing this operation.

20. DO NOT soak the appliance in water or other liquids, wash it under the tap, or let any liquid flow into the internal casing of the appliance to prevent electric shock. In case of accidental fall in water, DO NOT try to take it out, but first of all switch off the electric mains and unplug immediately the power adapter from the socket.

21. Avoid placing the power adapter on abrasive or sharp surfaces or in positions where it can be damaged easily. The power adapter must NOT be placed under carpets, or
    covered with throw rugs, runners or similar. Arrange the power adapter cable away from the high traffic area, and where it will NOT be tripped over.

22. In case of malfunction or anomaly during the functioning, switch off the appliance immediately, turn off the power and check the cause of the anomaly, if possible, with the support of a qualified person.

23. If smoke is observed coming out of the appliance whilst charging, switch off the electric mains, unplug immediately the power adapter from the socket. If smoke is observed coming out of the appliance whilst in operation, switch off power supply switch at the bottom of the appliance.

24. This appliance is NOT intended for commercial use but to be used in households and similar applications, such as:
    • Staff kitchen areas in shops, offices and other working environments;
    • Dormitories;
    • By clients in hotels, motels and other residential environments;
    • Bed and breakfast type environment.

25. DO NOT use or store the appliance outdoors. Store and use the appliance only indoors, or in any case, protected from weathering such as rain, direct radiation of the
    sun and dust.

26. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall NOT play with the appliance. Cleaning and user maintenance shall NOT be made by children unless they are older than 8 and supervised. Keep the appliance and its cable out of reach of children less than 8 years old.

27. Save these instructions.

How to use

The Charging Dock

1. Charging
During normal operation, place the Charging Dock against the wall and remove all obstructions 1 meter from the left and right sides, and 2 meters from the front of the Charging Dock.
Connect the Power Adapter Socket to the electric mains and insert the Power Adapter Cable into the Power Adapter Port of the Charging Dock and switch it ON, as shown in the figure below. The Charging Dock illuminates.

Press and hold:

• the “Start/Pause” button on the Remote Control, or
• the button on the appliance.

The backlit light of these buttons illuminates and the appliance enters Standby mode.
Press the “return” button of the Remote Control and the appliance will return to the Charging Dock for charging, as shown in in the figure below. This works for both Standby mode and Operating mode.

When the appliance is being charged for the first time, please ensure that it’s charged for an uninterrupted duration of at least 12 hours.
During the charging process, the green backlit illumination of

• the “Start/Pause” button on the Remote Control, or
• the button on the appliance

flicker. Pressing either of these two buttons when the appliance is being charged will send the appliance into Operating mode, and start the vacuuming process, with the appliance assuming control and it will adjust the type of vacuuming phase according to the environment of different floors and rooms.

However, it is highly recommended NOT to abort the charging process until the appliance is fully charged, before commencing vacuuming.
If you remove power from the Charging Dock, by switching off the electric mains, removing the Power Adapter Socket from the electric mains, or disconnecting the Power Adapter Cable from the Power Adapter Port, while the appliance is being charged, the backlit illumination of the these buttons will flicker alternately red & green in order to remind you to press either of these buttons again if you do not intend to use the appliance for a long time.
When the battery power is low, the red backlit illumination of these buttons flicker. The appliance will automatically start looking for the Charging Dock.
Please charge the appliance fully after every use. If you find abnormal overheating during charging, please stop charging immediately, otherwise it may cause leakage, heat generation or rupture the battery.
When the appliance has been fully charged, the green backlit illumination of these buttons will be constant.
In order to prolong the life of the battery, please charge it every 2 months even if the appliance was NOT in use.

2. Start /Pause
Pressing either of these two buttons:

• the “Start/Pause” button on the Remote Control, or
• the button on the appliance

will send the appliance into Operating mode, whereby the appliance assumes control in the “AUTO” phase where it will adjust the type of vacuuming phase according to the environment of different floors and rooms. You can change the vacuuming phase from “AUTO” to “focus” or “edge” within the Operating mode by pressing their respective buttons on the Remote Control.

Pressing either of these two buttons again causes the appliance to enter the Standby mode. If either of these two buttons is pressed again within 20 – 25 seconds, the  appliance returns to the Operating mode. Otherwise, the appliance enters the Sleep mode. The appliance toggles between the 3 modes according to the sequence below:

Standby mode → Operating mode → Standby mode → Operating mode
(if either of these two buttons is pressed within 20 – 25 seconds of entry into Standby mode), or Standby mode → Operating mode → Standby mode →
Sleep mode (if either of these two buttons is NOT pressed within 20 – 25 seconds of entry into Standby mode).

Sleep mode: the display is NOT illuminated, the appliance is at rest.
Standby mode: the display is illuminated, the appliance is at rest.
Operating mode: the display is illuminated, the appliance is vacuuming.

Note

• DO NOT leave the appliance on Standby mode for long intervals of time
• DO NOT operate the appliance while it is being charged

3. “AUTO”

In the Operating mode where the appliance is moving across the floor and performing “focus” or “edge” vacuuming, pressing the “AUTO” button on the Remote Control returns control of vacuuming back to the appliance, and it will adjust the type of vacuuming phase according to the environment of different floors and rooms.

In Operating mode, when the “AUTO” button on the Remote Control is pressed, nothing will happen and the appliance will remain in “AUTO” mode.

Pressing either of these two buttons:

• the “Start/Pause” button on the Remote Control, or
• the button on the appliance stops the appliance from operating.

In the Standby mode where the appliance is stationary, pressing either of these two buttons starts the vacuuming process, with the appliance assuming control and it will adjust the type of vacuuming phase according to the environment of different floors and rooms.

4. “focus”
In the Operating mode where the appliance is moving across the floor, when the appliance happens to be at the centre of the most dusty/dirty region, press the “focus” button on the Remote Control, and the appliance will focus on cleaning the area with vigorous & rigorous vacuuming.

In the Standby Mode where the appliance is stationary, carry the appliance and put down the appliance at the centre of the most dusty/dirty region, press the “focus” button on the Remote Control, and the appliance will focus on cleaning the area with vigorous & rigorous vacuuming.

Pressing either of these two buttons:

• the “Start/Pause” button on the Remote Control, or
• the button on the appliance stops the appliance from operating.

Once the task is completed, the appliance will enter the “AUTO” phase which returns control of vacuuming back to the appliance, and it will adjust the type of vacuuming phase according to the environment of different floors and rooms.

5. “edge”
In the Operating Mode where the appliance is moving across the floor, or in the Standby Mode where the appliance is stationary, pressing the “edge” button on the Remote Control instructs the appliance to seek out and vacuum along the largest edge of the room.

Pressing either of these two buttons:

• the “Start/Pause” button on the Remote Control, or
• the button on the appliance stops the appliance from operating.

Once the task is completed, the appliance will enter the “AUTO” phase which returns control of vacuuming back to the appliance, and it will adjust the type of vacuuming phase according to the environment of different floors and rooms.

Note After a sweeping mode is selected, the appliance will switch to another sweeping mode automatically according to the actual environment, so as to achieve the best sweeping effect

Under any sweeping mode, the appliance will stop sweeping when:

• the “Start/Pause” button on the Remote Control, or
• the button on the appliance.

Replacing the Battery

1. Press and hold the button on the appliance.
   

2. Use a screwdriver to remove screws of the Battery Cover at the top of the appliance.
   

3. After the Battery Cover is removed, take out the Battery from the Battery Case by pulling the insulating cloth strip on the Battery.

4. Unlock the Battery Connecting Plug to separate the old Battery from the appliance. Remove the old Battery.
   

5. Attach a new Battery to the Battery Connecting Plug. The colour of the new Battery wire corresponds to the colour of the appliance’s interface wire.
   

6. Insert the new Battery into the Battery Case with the characters face-up.

7. Arrange the wires next to the new Battery. Replace the Battery Cover and lock it securely, using a screwdriver, with the screws taken out previously.

8. Press and hold the button on the appliance. Check if the appliance works normally.
   Note
   a. The original manufacturer’s battery (Lithium battery 1500 mAh 11.1 V) must be used as replacement, otherwise the motor of the appliance may be damaged.
   b. After the battery is replaced, the new Battery has to be charged for an uninterrupted duration of at least 12 hours.
   c. In order to prolong the service life of the battery, when not in use for a long time, please take out the Battery from the Battery Case and place it in a cool and dry environment
   d. DO NOT use non-rechargeable batteries.
   e. DO NOT disassemble the battery pack.

How to clean

WARNING: The appliance must NEVER be used without the Preliminary Strainer and the Efficient Strainer contained within the Dustbin. Always place them back after cleaning them. When the suction power decreases, the strainers might be clogged. Using the appliance with a clogged strainer puts additional strain on the motor. Prompt removal of dust and dirt not only improves the efficiency of the appliance but only extends its working life.

1. Cleaning of side brushes
a. Wash the Left & Right side brushes with detergent, rinse them under running water and dry them naturally after use. If they are damaged and cannot work normally, please replace them.
Note: When attaching side brushes, please attach the corresponding “L” and “R” side brushes to the position “L” and “R” at the top of the appliance respectively.
2. Cleaning the Dustbin and Strainers
a. After you press the finger sign on the Swiveling Cover, the Cover will pop-up automatically.b. After taking out the Dustbin, extract and remove any foreign matter trapped in the Suction channel of the appliance. c. Remove the Efficient Strainer. d. Remove the Preliminary Strainer.

e. Invert the Dustbin until all dust is removed.

f. Clean the Dustbin, Preliminary Strainer and Efficient Strainer fully. The Efficient strainer should be cleaned after using it for 15 – 30 days. The maximum service life of the Efficient Strainer is 24 months. The Efficient strainer shall not be cleaned with a brush but shall be blown with a dryer or knocked slightly by virtue of an external force to make dust fall down. DO NOT wash it with water.

g. Assemble the Dustbin, Preliminary Strainer and Efficient Strainer in the correct sequence. Please ensure that the two strainers are assembled well to avoid damage to the appliance.

Note

• Please clean the Dustbin and the Suction channel after every use.
• After its components are washed with water, dry them dried naturally but NOT under strong sunlight. Once fully dried, reassemble the components in the appliance.
• If the Preliminary Strainer and the Efficient Strainer are damaged, replace them to avoid affecting the efficiency of the appliance.

3. Cleaning the Duster cloth
Remove the duster cloth, rinse it clean and dry it in the air.

The Duster Cloth is only available for models with Water Tank component.

4. Cleaning of Sensor lens & Electrodes
Use a cleaning tool or a piece of soft cloth to wipe the Sensors & Electrodes slightly. See positions indicated in the diagram below:
S – denotes positions of Sensors
E – denotes positions of Electrodes

5. Cleaning the Charging Dock
Use a cleaning tool or a piece of soft cloth to wipe the Charging Connectors on the Charging Dock. See positions indicated in the diagram below:

The Charging Dock

Solving Problems

ALARM CODE TABLE

Check the status of side brush.
3.| The red and orange lights flash alternately and the buzzer alarms.| The drive wheels are overloaded.| Check the left and right side wheels.
4.| The green and orange lights flash alternately.| Collision switch fault’| Check the flexibility of the bumper.
5 .| The orange light flickers for 60 s and the buzzer alarms for 10s.| Charging failure.| Replace qualified adapter or batteries.
6.| If the problem cannot be solved with the method above, please try the following actions| Switch on the power supply at the bottom of the appliance again and restart the appliance.
If the problem cannot be solved by restarting, please send the appliance to the authorised service centre for maintenance.

ENVIRONMENTAL TIP

This appliance, along with all other electronic appliances, should, when it is no longer capable of functioning, be disposed with the least possible environmental damage according to the local regulations in your area. In most cases you can discard the appliance at your local recycling center.
DISPOSAL: Do not dispose this appliance as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. Please dismantle the battery from the appliance before it is scrapped. When the battery is dismantled, please ensure that it is switched off. Please recycle the scrapped battery for safety and environmental protection.

WARRANTY

The manufacturer provides warranty in accordance with the legislation of the customer’s own country of residence, with a minimum of 1 year, starting from the date on which the appliance is sold to the end user.
The warranty covers defects in material and workmanship.
The repairs under warranty may only be carried out by an authorised service centre. When making a claim under the warranty, the original bill of purchase (with purchase date clearly indicated) must be submitted.

The warranty will not apply in cases of:

• normal wear and tear
• if the steps (as laid out in the section regarding Warnings) have not been observed e.g. overloading of the appliance, use of non-approved accessories
• if the appliance has not been properly maintained, if force has been used against it or if it has been damaged in any other way
• damage caused by non-observance of the user manual or non-compliance with the installation instructions
• errors or faults owing to defects in the distribution system
• if the appliance has been repaired or modified or changed in any way or by any person not properly authorized

 SPECIFICATION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>