WyreStorm EXP-EX-80-KVM HDMI KVM Extender Set with USB 2.0 Extension User Guide
- June 6, 2024
- WyreStorm
Table of Contents
HDMI KVM Extender Set
with USB 2.0 Extension
EXP-EX-80-KVM
Quickstart Guide
WyreStorm recommends reading through this document in its entirety to become
familiar with the product’s features prior to starting the installation
process.
IMPORTANT!
Installation Requirements
- Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.
- Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
In the Box
1x EXP-EX-80-KVM Transmitter
1x EXP-EX-80-KVM Receiver
1x 12V DC 2A Power Supply (US/UK/EU/AU)
1x USB Type B to Type-A Cable
4x Mounting Brackets
Basic Wiring Diagram
Transmitter (Front/Rear)
A HDMI In | 19-pin type A HDMI female Supports HDMI and DVI/D with adapter |
---|---|
B Power LED | Solid: The unit is powered On |
Off: The unit is powered Off
C Power In| 5.5mm Screw Down Barrel Jack Connect to the included 12V DC
2A power supply to the transmitter. A power supply is not required on the
other end as it will be powered using PoC.
D Status LED| Flashing: The receiver is operating normally.
Off: The receiver is not operating normally.
E UTP Out| 8-pin RJ-45 female Connect the transmitters UTP OUT to
receivers UTP IN.
F USB LED| Solid : USB linked
Flashing : USB data transmitting
Off : No USB device connected
G USB (PC) Host| USB Type B female Connection of USB Host device
Receiver (Front/Rear)
A HDMI Out| 19-pin type A HDMI female Supports HDMI and DVI/D with
adapter
---|---
B Power LED| Solid: The unit is powered On
Off: The unit is powered Off
C Power In| 5.5mm Screw Down Barrel Jack Connect to the included 12V DC
2A power supply to the transmitter. A power supply is not required on the
other end as it will be powered using PoC.
D Status LED| Flashing: The receiver is operating normally.
Off: The receiver is Not operating normally.
E UTP In| 8-pin RJ-45 female Connect the transmitters UTP OUT to
receivers UTP IN.
F USB LED| Solid: USB linked
Flashing: USB data transmitting
Off: No USB device connected
G USB Device| 2x USB Type-A female
Connection of USB devices such as keyboards and mice.
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
- The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on the signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
- WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
- WyreStorm recommends using pre-terminated HDMI cables due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
- Verify that power is being supplied to the transmitter and receiving device
- Verify that all HDMI and UTP connections are not loose and are functioning properly
- Verify that the UTP cable is properly terminated following EIA568B standard
- Verify that the output resolution of the source and display is supported by this extender
Failed USB Connection or Slow Transmission rate
- Ensure the category cable length is within the range of requirement, USB HID device is within 80m/260ft, USB storage device is within 60m/200ft.
Troubleshooting Tips:
- WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.
Specifications
|
Transmitter
|
Receiver
---|---|---
Audio and Video
Inputs| 1x HDMI In: 19-pin type A
1x USB Type B
| 1x UTP In: 8-pin RJ-45 Female
2x USB Type A
Outputs| lx UTP Out: 8-pin RJ-45 Female| 1x HDMI Out: 19-pin type A
Output Video Encoding| UTP
Encoding Data Rate| 6.75Gbps
End to End Latency (Max)| 10ps (microseconds)
Audio Formats| 2ch PCM I Multichannel up to DTS-X and Dolby Atmos
Video Resolutions (Max)| Video Resolution| HDMI| Cat6|
Cat6a/7
1920x1080p @60Hz 12bit| 15m/49ft| 80m/262ft| 80m/262ft
Note: WyreStorm recommends the use of shielded category cable to minimize
signal noise and interference
Supported Standards| DCI 1 RGB
Maximum Pixel Clock| 225MHz
Communication and Control
HDMI| HDMI 1.3b I HDCP 1.41 EDID I DVI/D supported with adapter (not
included)
UTP| HDMI 1.3b 1 HDCP 1.41 EDID 12-way PoC
USB|
Power
Power Supply|
PoC| IEEE 802.3af 48V 15.4W Max 12-way
Max Power Consumption| 3.6W (per unit)
Environmental
Operating Temperature| 0 to + 45°C (32 to + 113 °F), 10% to 90%, non-
condensing
Storage Temperature| -20 to +70°C (-4 to + 158 °F), 10% to 90%, non-
condensing
Maximum BTU| 12.28 BTU/hr
Dimensions and Weight
Rack Units/Wall Box| <1U
Height| 23mm/0.9in
Width| 75mm/2.95276in
Depth| 98.2mm/3.87in
Weight| 0.22kg/0.48lb (each)
Regulatory
Safety and Emission| CE | FCC | RoHS | RCM | EAC
Note: WyreStorm reserves the right to change product specification, appearance, or dimensions of this product at any time without prior notice.
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a period of two (2) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
Copyright © 2020 WyreStorm Technologies |
wyrestorm.com
EXP-EX-80-KVM Quickstart Guide | 200330
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>