HiKOKI C 6MEY Cordless Circular Saw Instructions
- June 3, 2024
- HiKOKI
Table of Contents
C 6MEY Cordless Circular Saw
Instructions
Handling instructions
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock,
fire, and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep the work area clean and well-lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust.
Power tools create sparks that may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power to ol.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet condition s.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool.
Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
The use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply.
The use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing, and use common sense when
operating a power tool.
Do not use a power tool while you are tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust masks, non-skid safety shoes, hard hats, or
hearing protection used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position
before connecting to a power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing, and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application.
The correct power tool will do the job better and safer at the rate for which
it was designed.
b) Do not use the power tool if the switch does not turn on an d off.
Any power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/ or the battery pack from
the power tool before making any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may affect the power tool
operation.
If damaged, have the power tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with
these instructions, taking into account the working conditions and the work to
be performed.
Use of the power tool for operations different from those intended could result
in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts.
This will ensure that the safety of the power tool is maintained.
PRECAUTION
Keep children and infi rm persons away. When not in use, tools should be stored
out of reach of children and infi rm persons.
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
a) DANGER: Keep hands away from cutting area and the blade. Keep your
second hand on auxiliary handle, or motor housing.
If both hands are holding the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece.
The guard cannot protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the workpiece.
Less than a full tooth of the blade teeth should be visible below the
workpiece.
d) Never hold piece being cut in your hands or across your leg. Secure the
workpiece to a stable platform.
It is important to support the work properly to minimize body exposure, blade
binding, or loss of control.
e) Hold the power tool by insulated gripping surfaces only, when performing
an operation where the cutting tool may contact hidden wiring or its own
cord.
Contact with a “live” wire will also make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
f) When ripping, always use a rip fence or straight-edge guid e.
This improves the accuracy of cut and reduces the chance of blade binding.
g) Always use blades with the correct size and shape (diamond versus round)
of arbor holes.
Blades that do not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
h) Never use damaged or incorrect blade washers or bolts.
The blade washers and bolts were specially designed for your saw, for optimum
performance and safety of operation.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched, bound or misaligned saw blade,
causing an uncontrolled saw to lift up and out of the workpiece toward the
operator;
– when the blade is pinched or bound tightly by the kerf closing down, the
blade stalls, and the motor reaction drives the unit rapidly back toward the
operator;
– if the blade becomes twisted or misaligned in the cut, the teeth at the back
edge of the blade can dig into the top surface of the wood causing the blade
to climb out of the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions as given below.
a) Maintain a fi rm grip with both hands on the saw and position your arms
to resist kickback forces.
Position your body to either side of the blade, but not in line with the
blade.
Kickback could cause the saw to jump backward, but kickback forces can be
controlled by the operator, if proper precautions are taken.
b) When the blade is binding, or when interrupting a cut for any reason,
release the trigger and hold the saw motionless in the material until the
blade comes to a complete stop. Never attempt to remove the saw from the
work or pull the saw backward while the blade is in motion or kickback may
occur.
Investigate and take corrective actions to eliminate the cause of blade
binding.
c) When restarting a saw in the workpiece, center the saw blade in the kerf
and check those saw teeth are not engaged in the material.
If the saw blade is binding, it may walk up or kick back from the workpiece as
the saw is restarted.
d) Support large panels to minimize the risk of blade pinching and kickba
ck.
Large panels tend to sag under their own weight. Supports must be placed under
the panel on both sides, near the line of cut, and near the edge of the panel.
e) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce narrow kerfs causing excessive
friction, blade binding, and kickback.
f) Blade depth and bevel adjusting locking levers must be tight and secure
before making a cut.
If blade adjustment shifts while cutting, it may cause binding and kickback.
g) Use extra caution when sawing into existing walls or other blind
areas.
The protruding blade may cut objects that can cause kickback.
Lower guard function
a) Check the lower guard for proper closing before each use. Do not operate
the saw if the lower guard does not move freely and close instantly. Never
clamp or tie the lower guard into the open position
If the saw is accidentally dropped, the lower guard may be bent. Raise the
lower guard with the retracting handle and make sure it moves freely and does
not touch the blade or any other part, in all angles and depths of the cut.
b) Check the operation of the lower guard spring. If the guard and the
spring are not operating properly, they must be serviced before use.
The lower guard may operate sluggishly due to damaged parts, gummy deposits,
or a build-up of debris.
c) Lower guard may be retracted manually only for special cuts such as
“plunge cuts” and “compound cuts”.
Raise the lower guard by retracting the handle and as soon as the blade enters
the material, the lower guard must be released.
For all other sawing, the lower guard should operate automatically.
d) Always observe that the lower guard is covering the blade before placing
the saw down on the bench or floor.
An unprotected, coasting blade will cause the saw to walk backward, cutting
whatever is in its path. Be aware of the time it takes for the blade to stop
after the switch is released.
ADDITIONAL SAFETY WARNINGS
-
Use only blade diameter specifi ed on the machine.
-
Do not use any abrasive wheel.
-
Do not use saw blades that are deformed or cracked.
-
Do not use saw blades made of high-speed steel.
-
Do not use saw blades that do not comply with the characteristics specifi ed in these instructions.
-
Do not stop the saw blades by lateral pressure on the disc.
-
Always keep the saw blades sharp.
-
Ensure that the lower guard moves smoothly and freely.
-
Never use the circular saw with its lower guard fixed in the open position.
-
Ensure that the retraction mechanism of the guard system operates correctly.
-
Wear earplugs to protect your ears during the operation.
-
Never operate the circular saw with the saw blade turned upward or to the side.
-
Ensure that the material is free of foreign matters such as nails.
-
The saw blade range should be from 165 mm to 162 mm.
-
Disconnect the plug from the receptacle before carrying out any adjustment, servicing or maintenance.
-
Be careful of brake kickback. This circular saw features an electric brake that functions when the switch is released. As there is some kickback when the brake functions, be sure to hold the main body securely.
-
Ensure that the power source to be utilized conforms to the power requirements specifi ed on the product nameplate.
-
Ensure that the power switch is in the OFF position. If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident.
-
When the work area is removed from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as
practicable. -
Avoid cutting in the state where the base has floated up from the material. When the blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.
-
Support large panels to minimize the risk of blade pinching and KICKBACK. Large panels tend to sag under their own weight (Fig. 3). Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel as shown in Fig. 2. To minimize the risk of blade pinching and kickback. When cutting operation requires the resting of the saw on the workpiece, the saw shall be rested on the larger portion and the smaller piece cut off.
-
Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK. NEVER place your hand or fi ngers behind the saw (Fig. 4). If kickback occurs, the saw could easily jump backward over your hand, possibly causing severe injury.
-
WARNING: It is important to support the workpiece properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Fig. 5 illustrates the typical hand support of the saw.
-
Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 6 illustrates the RIGHT way to cut off the end of the board, and Fig. 7 the WRONG way. If the workpiece is short or small, the clamp is down. DON’T TRY TO HOLD SHORT PLACES BY HAND!
-
Never attempt to saw with the circular saw held upside down in a vise. This is extremely dangerous and can lead to serious accidents (Fig. 8).
-
Should the lever remain loosened, it will create a very hazardous situation. Always thoroughly clamp it. (Fig. 12)
-
It is very hazardous to allow the wing bolt to remain loosened. Always thoroughly clamp it. (Fig. 23)
-
Prior to the cutting operation, make sure the material you are going to cut. If the material to be cut is expected to generate harmful/toxic dust, make sure the dust bag or appropriate dust extraction system is connected to the dust outlet tightly.
Wear the dust mask additionally, if available.
○ Before starting to saw, confi rm that the saw blade has attained full-speed revolution.
○ Should the saw blade stop or make an abnormal noise while operating, promptly turn OFF the switch.
○ Always take care in preventing the power cord from coming near to the revolving saw blade.
○ Using the circular saw with the saw blade facing upwards or sideways is very hazardous. Such uncommon applications should be avoided.
○ When cutting materials, always wear protective glasses.
○ When finished with a job, pull out the plug from the receptacle. -
After having attached the saw blade, reconfi rm that the lock lever is firmly secured in the prescribed position.
-
Do not expose directly your eye to the light by looking into the light.
If your eye is continuously exposed to light, your eye will be hurt.
NAMES OF PARTS (Fig. 1 – Fig. 27)
1 | Switch |
---|---|
2 | Switch lock |
3 | Cutting depth lever |
4 | Incline wing nut |
5 | Guide fastener wing bolt |
6 | Lower guard |
7 | Bolt |
8 | Washer (B) |
9 | Saw blade |
10 | Guide piece |
11 | Base |
12 | Incline lever |
13 | Lock lever |
14 | Guide fastener wing bolt |
15 | Stopper lever |
16 | LED light |
17 | Cord holder |
18 | Handle |
19 | Mode selector switch |
20 | Silent mode indicator lamp |
21 | Lighting switch |
22 | Long guide |
23 | Guide |
24 | Fluorine plate |
25 | Dust collection adapter |
26 | Box wrench |
27 | Washer (A) |
SYMBOLS
WARNING
The following show symbols used for the machine. Be sure that you understand
their meaning before use.
| C6MEY: Circular Saw
---|---
| To reduce the risk of injury, users must read the instruction manual.
| Always wear eye protection.
| Always wear hearing protection.
| Only for EU countries Do not dispose of electric tools together with
household waste material! In observance of European Directive 2002/96/ EC on
waste electrical and electronic equipment and its implementation in accordance
with national law, electric tools that have reached the end of their life must
be collected separately and returned to an environmentally compatible
recycling facility.
V| Rated voltage
| No-load speed
| Switching ON
| Switching OFF
| Disconnect the mains plug from the electrical outlet
| Mode selector switch
| Lighting switch
| Prohibited action
| Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the accessories
listed on page 154.
Standard accessories are subject to change without notice.
APPLICATIONS
Cutting various types of wood.
SPECIFICATIONS
Model | C6MEY |
---|---|
Voltage | 230 V |
Power Input | 1050 W |
No-Load Speed | 4100 min-1 (Power mode) |
2500 min-1 (Silent mode)
Capacity| Cutting
depth| 900°| 66 mm
45°| 45 mm
Weight*| 2.8 kg
- According to EPTA-Procedure 01/2003
NOTE
Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.
Electronic control
○ Soft-start
○ Overload protection
This protection feature cuts off the power to the motor in the event of overloading of motor or a conspicuous reduction in rotational speed during operation.
When the overload protection feature has been activated, the motor may stop.
In this case, release the tool switch and eliminate the causes of overloading.
After that, you can use it again.
○ Overheat protection
This protection feature cuts off the power to the motor and stops the power tool in the event of overheating of the motor during operation.
When the overheat protection feature has been activated, the motor may stop.
In this case, release the tool switch and cool it down for a few minutes.
After that, you can use it again.
○ Rotation speed changeover function (Power mode / Silent mode) (Power mode / Silent mode switch function)
Each press of the Mode Selector Switch changes the operating mode. (Fig. 15)
Silent mode reduces maximum motor RPM enabling efficient work with less noise.
The Silent Mode Indicator Lamp lights in Silent mode.
When the load increases during Silent mode, the tool will automatically switch to Power mode and revert back to Silent mode when the load decreases.
In Power mode, no change is made to Silent mode even when the load decreases.
NOTE
○ To enable mode changes, pull the switch once after connecting the main plug.
○ Do not give a strong shock to the switch panel or break it.
It may lead to trouble.
MOUNTING AND OPERATION
Action | Figure | Page |
---|---|---|
Fine-tuning of parallelism | 9 | 156 |
Fine-tuning of perpendicularity | 10 | 156 |
Fine-tuning of guide piece position | 11 | 156 |
Adjusting the cutting depth | 12 | 157 |
Cutting line | 13 | 157 |
Switch operation | 14 | 157 |
About the mode select function (*1) | 15 | 157 |
Using the LED light | 16 | 157 |
Using the cord holder | 17 | 157 |
Attaching the long guide (sold separately) | 18 | 158 |
Attaching the guide (sold separately) | 19 | 158 |
Attaching the fluorine plate (sold separately) | 20 | 158 |
Attaching the dust collection adapter (sold separately) | 21 | 158 |
Cutting at right angles | 22 | 158 |
An inclined cutting (+45° direction) | 23 | 159 |
Inclined cutting (-5° direction) | 24 | 159 |
Dismounting the saw blade | 25 | 160 |
Mounting the saw blade | 26 | 160 |
Selecting accessories | ― | 162 |
*(1) About the mode select function**
Each time the mode selector switch is pushed, the operation mode changes.
When Silent mode is selected, the Silent mode indicator lamp lights up.
Silent mode reduces maximum motor RPM enabling efficient work with less noise.
If the load increases while the motor is operating in Silent mode, it
automatically changes to Power mode.
Additionally, if the load decreases again, it automatically returns to Silent
mode.
In Power mode, no change is made to Silent mode even when the load decreases.
Mode | No-load speed |
---|---|
Power | 4100 min-1 |
Silent | 2500 min-1 |
NOTE
○ You cannot change the mode unless the power plug is connected to a
receptacle and the switch is pulled once.
○ Even if the switch is turned on and off or the power plug is disconnected and
connected, this unit will maintain the mode that you set.
LED LIGHT WARNING SIGNALS (Fig. 27)
This product features functions that are designed to protect the tool itself.
While the switch is pulled and 3 seconds after its release, if any of the
safeguard functions are triggered during operation, the LED light will blink
as described in Table 1. When any of the safeguard functions are triggered,
immediately remove your fi nger from the switch and follow the instructions
described under corrective action.
Table 1
Safeguard Function | LED Light Display | Corrective Action |
---|---|---|
Overburden Protection | On 0.1 second/off 0.1 second![HiKOKI C 6MEY Cordless |
Circular Saw icon 2](https://manuals.plus/wp-content/uploads/2022/10/HiKOKI-C
-6MEY-Cordless-Circular-Saw-icon-2.png)| Remove the cause of the
overburdening.
Temperature Protection| On 0.5 second/off 0.5 second| Allow the tool to thoroughly cool.
MAINTENANCE AND INSPECTION
-
Inspecting the saw blade
Since the use of a dull saw blade will degrade and cause possible motor malfunction, sharpen or replace the saw blade as soon as abrasion is noted. -
Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazards. -
Maintenance of the motor
unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. -
Replacing supply cord
If the replacement of the supply cord is necessary, this has to be done by the manufacturer of this agent in order to avoid a safety hazard. -
Maintenance of lower guard
For safe and proper working, always keep the machine and ventilation slots clean. The lower guard must always be able to more freely and retract automatically. Therefore, always keep the area around the lower guard clean. Remove dust and chips by blowing out with compressed air or with a brush. -
Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics. -
Storage
Please avoid locations such as the following for the storage of products and accessories that are not being used, and store them in a safe and dry place.
NOTE
- Do not store them in locations where children can reach them or easily get hold of them.
- Do not store them in locations where rain can fall such as under the eaves of a house, or where there is humidity.
- Do not store them in locations where there are sudden changes in humidity or there is direct sunlight.
- Do not store them in locations where there are volatile substances that have a risk of catching fi re or exploding.
CAUTION: In the operation and maintenance of power tools, the safety
regulations and standards prescribed in each country must be observed.
GUARANTEE
We guarantee HiKOKI Power Tools in accordance with statutory/country specifi c
regulations. This guarantee does not cover defects or damage due to misuse,
abuse, or normal wear and tear. In case of a complaint, please send the Power
Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this
Handling instruction, to a HiKOKI Authorized Service Center.
IMPORTANT
Correct connection of the plug The wires of the main lead are colored in
accordance with the following code:
Blue: — Neutral
Brown: — Live As the colors of the wires in the main lead of this tool may not
correspond with the colored markings identifying the terminals in your plug
proceed as follows: The wire colored blue must be connected to the terminal
marked with the letter N or colored black.
The wire colored brown must be connected to the terminal marked with the
letter L or colored red. Neither core must be connected to the earth’s
terminal.
NOTE: This requirement is provided according to BRITISH STANDARD 2769:
1984. Therefore, the letter code and color code may not be applicable to other
markets except The United Kingdom.
Information concerning airborne noise and vibration
The measured values were determined according to EN60745 and declared in
accordance with ISO 4871.
Measured A-weighted sound power level: 94 dB (A)
Measured A-weighted sound pressure level: 83 dB (A)
Uncertainty K: 3 dB (A). Wear hearing protection.
Vibration total values (triax vector sum) determined according to EN60745.
Cutting chipboard: Vibration emission value ah = 2.0 m/s2
Uncertainty K = 1.5 m/s2.
The declared vibration total value has been measured in accordance with a
standard test method and may be used for comparing one tool with another. It
may also be used in a preliminary assessment of exposure.
WARNING
- The vibration emission during actual use of the power tool can diff er from the declared total value depending in the ways in which the tool is used.
- Identify safety measures to protect the operator that is based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
NOTE
Due to HiKOKI’s continuing program of research and development, the specifi
cations herein are subject to change without prior notice.
|
---|---
|
|
|
GUARANTEE CERTIFICATE
- Model No.
- Serial No.
- Date of Purchase
- Customer Name and Address
- Dealer Name and Address (Please stamp dealer name and address)
Hikoki Power Tools (U.K.) Ltd.
Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ,
United Kingdom
Tel: +44 1908 660663
Fax: +44 1908 606642
URL: http://www.hikoki-powertools.uk
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that Circular Saw, identified by type
and specifi c identifi cation code 1), is in conformity with all relevant
requirements of the directives 2) and standards 3).
Technical fi le at 4) – See below.
The European Standard Manager at the representative office in Europe is
authorized to compile the technical file.
The declaration is applicable to the product affixed CE marking.
1) C6MEY C346193R
2) 2006/42/EC, 2014/30/EU, 2011/65/EU
3) EN60745-1:2009+A11:2010
EN60745-2-5:2010
EN55014-1:2006+A1:2009+A2:2011
EN55014-2:1997+A1:2001+A2:2008
EN61000-3-2:2014
EN61000-3-3:2013
4) Representative office in Europe
Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 Willich, Germany
Head offi in Japan
Koki Holdings Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
29. 6. 2018
Naoto Yamashiro
European Standard Manager
29. 6. 2018
A. Nakagawa
Corporate Offi cer
Koki Holdings Co.” Ltd.
806
Code No. C99712773 G
Printed in China
Documents / Resources
|
HiKOKI C 6MEY Cordless Circular
Saw
[pdf] Instructions
C 6MEY, Cordless Circular Saw, Circular Saw, Cordless Saw, Saw
---|---
References
- Strona główna | HIKOKI
- HiKOKI Power Tools Österreich - High Performance Power Tools
- Home Banner
- Home - Hikoki-powertools.cz
- HiKOKI Power Tools Deutschland - High Performance Power Tools
- HiKOKI Power Tools
- HiKOKI Power Tools Ibérica - HiKOKI
- Hikoki powertools
- HiKOKI - High Performance Power Tools
- HiKOKI Power Tools
- HiKOKI Power Tools
- HiKOKI
- Hikoki Powertools
- HiKOKI Power Tools
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>