REELY 2595543 1:16 4WD Crawler Mini Freemen, RtR User Manual

Operating Instructions
1:16 4WD Crawler Mini Freemen, RtR
Item no: 2595543 (Matt Grey)
Item no: 2595544 (Matt Black)

Intended use

The product is a remote controlled 4WD vehicle with front and rear lights.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery contents

• Car
• Remote control
• USB charging cable
• 4x AA 1.5 V batteries
• Not a toy flyer
• Operating instructions

Latest product information

Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website

Description of symbols

The following symbols are on the product/appliance or are used in the text:
The symbol warns of hazards that can lead to personal injury.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

5.1 General

• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• If you have questions which remain unanswered by this information product, contact our technical support service or other technical personnel.
• Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

5.2 Handling

• Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

5.3 Operating environment

• Do not place the product under any mechanical stress.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
• Protect the product from high humidity and moisture.
• Protect the product from direct sunlight.

5.4 Operation

• Consult an expert when in doubt about the operation, safety or connection of the product.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
  – is visibly damaged,
  – is no longer working properly,
  – has been stored for extended periods in poor ambient conditions or
  – has been subjected to any serious transport-related stresses.

5.5 LiPo battery (car)

• The rechargeable battery is permanently built into the product and cannot be replaced.
• Never damage the rechargeable battery. Damaging the casing of the rechargeable battery might cause an explosion or a fire! Unlike conventional batteries/rechargeable batteries (e.g. AA or AAA type), the casing of the LiPo rechargeable battery does not consist of a thin sheet but rather a sensitive plastic film only.
• Never short-circuit the contacts of the rechargeable battery. Do not throw the battery or the product into fire. There is a danger of fire and explosion!
• Charge the rechargeable battery regularly, even if you do are not using the product. Due to the rechargeable battery technology being used, you do not need to discharge the rechargeable battery first.
• Never charge the rechargeable battery of the product unattended.
• When charging, place the product on a surface that is not heat-sensitive. It is normal that a certain amount of heat is generated during charging.

5.6 Batteries (remote control)

• Correct polarity must be observed while inserting batteries.
• The batteries should be removed from the device if it is not used for a long period of time to avoid damage through leaking. Leaking or damaged batteries might cause acid burns when in contact with skin, therefore use suitable protective gloves to handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying around, as there is risk, that children or pets swallow them.
• All batteries should be replaced at the same time. Mixing old and new batteries in the device can lead to battery leakage and device damage.
• Batteries must not be dismantled, short-circuited or thrown into fire. Never recharge non-rechargeable batteries. There is a risk of explosion!

Product overview

6.1 Car

6.2 Remote control

A 50/75/100: Speed control
C Power button
E CH4: Car lights ON/OFF
G S.LED: Power / low battery indicator
I SR: Steering range
K Throttle (forward / stop / reverse)| B ST-R: Steering reverse
D Battery compartment
F CH3: No function
H C.LED: No function
J ST: Steering trim
L Steering
---|---

Insert batteries (remote control)

1. Open the battery compartment.
2. Insert batteries matching polarities shown on the inside of the compartment cover.
3. Replace the compartment cover.

Recharge batteries (car)

Preconditions:
You have a suitable 5 V/DC 500 mA USB-A power supply.

1. Connect one end of the charging cable to the charging input on the product.

2. Connect the other end of the charging cable to a suitable power supply.

3. The status light on the car:
   – Blinks: charging in progress.
   – Solid on: charging is complete.

4. When the battery is charged, disconnect the charging cable.

Remote control

9.1 Low battery warning
Replace the remote-control battery when the S.LED light flashes slowly.

9.2 Binding remote to car
The remote control and the car should already be bound when you receive it.
If the connection is broken, follow these steps to repair the connection:
Preconditions:
Remote control and car are both powered OFF.

1. Press and hold the power button on the car until the status LED blinks rapidly.
2. Press and hold the power button on the remote control until the status LED S.LED blinks rapidly.
3. Wait a few moments for the binding process to complete.
   →  When the status lights on the car and remote control are steady ON, the binding process is complete.

9.3 Settings

straight.
CH4| Control lights| Switch the car lights ON/OFF.

Operation

Note:
For various settings and adjustments, refer to section: 9.3 Settings.

1. Press and hold the power button on the remote to switch the power ON.
2. Press and hold the power button on the car to switch the power ON.
3. Control the car using the throttle and steering wheel.
4. When finished driving:
   – Switch the car OFF
   – Switch the remote control OFF

Cleaning and care

Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.

1. Disconnect the product from the charger.
2. Clean the product with a dry, fibre-free cloth.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product conforms to the 2014/53/EU directive.

• Click on the following link to read the full text of the EU declaration of conformity: www.conrad.com/downloads
  Enter the product item number in the search box. You can then download the EU declaration of conformity in the available languages.

Disposal

13.1 Product

This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life. Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):

• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE  may apply in countries outside of Germany.

13.2 (Rechargeable) batteries
Remove batteries/rechargeable batteries, if any, and dispose of them separately from the product. According to the Battery Directive, end users are legally obliged to return all spent batteries/rechargeable batteries; they must not be disposed of in the normal household waste.
**** Batteries/rechargeable batteries containing hazardous substances are labelled with this symbol to indicate that disposal in household waste is forbidden. The abbreviations for heavy metals in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our stores or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations and contribute to environmental protection. Batteries/rechargeable batteries that are disposed of should be protected against short circuit and their exposed terminals should be covered completely with insulating tape before disposal. Even empty batteries/rechargeable batteries can contain residual energy that may cause them to swell, burst, catch fire or explode in the event of a short circuit.

Technical data

14.1 Car
Rechargeable battery ……………… LiPo 3.7 V 500 mAh
Charging current………………………………. max. 0.5 A
Battery recharge time ……………………….. approx. 60 mins
Runtime ………………………………………….. approx. 70 mins
Speed …………………………………………….. max. 5 km/h
ESC ……………………………………………….. yes
Ground clearance …………………………….. 19.5 mm
Wheelbase………………………………………. 142 mm
Tires (front & rear) ……………………………. Width:16 mm
Diameter: 47 mm
Track width: 87 mm
Dimensions (W x H x L)…………………….. 105 x 101 x 254 mm
Weight ……………………………………………. 268 g
14.2 Transmitter (remote control)
Input power……………………………………… 6 V/DC (4x 1.5 V AA batteries)
Frequency range ……………………………… 2410 – 2465 MHz
Transmission power …………………………. 10 mW
Transmission distance………………………. 80 m (open area)
Dimensions (W x H x L)…………………….. 135 x 90 x 185 mm
Weight ……………………………………………. 158 g (without batteries)
14.3 Charging cable
Input ………………………………………………. 4.5 – 5.5 V via USB-A
Output…………………………………………….. 4.425 V (outer: ø2.0 mm / inner: ø0.6 mm)
Wire length ……………………………………… 500 mm
Weight ……………………………………………. 10.5 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited. This publication reflects the technical status at the time of printing.
Copyright by Conrad Electronic SE.
*2595543_2595544_V1_0722_dh_mh_en 611289739-2 I1/O1 en

http://www.conrad.com/downloads

References

• Conrad Electronic » All parts of success
• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>