AMETA K30 Smart Mini Drone User Manual

AMETA K30 Smart Mini Drone

USER MANUAL

Please read th is man ua I carefully before flying and keep it for future use.

• For your safety, please follow the rules and safety guidelines whether you’ re a beginner or an expert at flying drones.

• According to the relevant laws and regulations in US, all drones must be registered, except those that weigh 0.55 pounds or less (less than 250 grams) and are flown exclusively under the Exception for Recreational Flyers. Please log in to the website of https://faadronezone-access.faa.gov/#/ to complete the registration.
  Make sure to observe local laws and regulations about the take-off weight. If the buyer does not register timely, SNAPTAIN will not be responsible for any losses, penalties and injuries caused by illegal flights.

• To meet the electromagnetic requirements of aviation on the radio station, it is forbidden to fly drones within 6.21 miles(l0km) on both sides of the runway centerline, or within 12.43 miles(20km) of both ends of the runway. It is also prohibited to fly a drone on the route of an airline. In the area that is prohibited by the relevant authority or d epa rtm ent of your country, stop using a II flying models and unmanned quad rotors.

• Please down load the B4U FLY App from Google Play or App Store, which provides real-time information about airspace restrictions and other flying requirements based on yourGPS location.

• Beginning September 16, 2023, all drone pilots who are required to register their UAS must operate in accord a nee with the rule on Remote ID.

Bright Skies” HOPRX’ Vibes

• Thank you for choosing our product and puttingyour trust in us. Contact us via email at support@snaptain.com or call us {415)991-6646{Mon-Fri)
• if you have questions or concerns a bout the product.
• We hope our products will make flying a whole new experience for you!
• Please read the manual carefullyforthe best use of this product.

FLIGHT SAFETY

• This drone is exclusively designed for indoor flying. Please do not use it outdoors to prevent the risk of losing it.

  1. For the safety of your property, keep the drone within your visual range during flight.
  2. Drones are made of materials including metal, fiber, plastic, and electronic components. Avoid prolonged exposure to direct sunlight and keep them away from any heat sources. Excessive heat can cause deformation and damage.
  3. Drones consist of various precision electronic and mechanical parts. Therefore, make sure that moisture and water do not enter the drone to prevent mechanical or electronic component failures that could lead to accidents.
  4. The performance of the drone and battery can be affected by environmental factors such as air density and temperature. Exercise caution when flying at altitudes above 3281 ft (1000 m) above sea level, as the performance of the battery and drone may be reduced.
  5. To avoid interference between the drone and other wireless devices, please turn off other wireless devices while using the drone.
  6. Avoid flying in areas where magnetic or radio interference may occur, such as near Wi-Fi hotspots, routers, Bluetooth devices, high-voltage power lines, high-voltage power transmission stations, mobile base stations, or broadcast towers. Flying in areas where interference can disrupt communication between the drone and remote may adversely affect flight direction and positioning accuracy, possibly resulting in loss of control. Interference can also cause errors in the video downlink connection.
  7. Be cautious around children. Avoid placing fingers in the rotating propellers.
  8. Inside the packaging are small accessories. Do not swallow them. Seek immediate medical help if accidentally ingested.
  9. Secure valuable items during indoor flights to prevent accidental damage due to operational errors.

BATTERY SAFETY

• RISK OF EXPLOSION BATTERY IS REPLACED BY AN INCORRECT TYPE

• DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

• BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY

• Under no circumstances should the battery touch any liquids. Avoid using the battery in rainy or wet conditions, as it may catch fire or explode unexpectedly.

• It is not allowed to use batteries that are not provided by the manufacturer. Additionally, it is advisable to use the package-included USB charging cable for charging the batteries.

• Batteries that are swollen, leaking, or damaged are strictly forbidden.

• It is recommended to use the battery between -l0°C and 40°C overheating may lead to a fire or explosion. A battery’s performance can be adversely affected by extremely low tern peratu res.

• Do not insert or puncture the battery with any sharp object.

• Battery liquid is highly corrosive, so stay away if it leaks. If skin or eyes are contacted, rinse immediately with plenty of water and seek medical attention.

• Please keep the battery out of children’s reach. Immediately seek medical attention if a child swallows parts.

• After being dropped or impacted, the battery should not be used again.
  Place the battery away from heat sources, such as a car in direct sunlight or on a hot day, a fire or a stove.

• To prevent a battery from entering an over-discharged state, avoid storing it for extended periods of time once it has been fully discharged. If a battery is overcharged, the battery cell will be damaged and unable to be recharged.

WHAT’S INCLUDED

PRODUCT OVERVIEW

Drone

*How to Replace the Propeller Assembly (Optional)

1. Carefully remove the propeller guard by lifting the pins one by one from the drone.
2. Insert the removal tool into the gap between the propeller and the motor. Gently pry the propeller upward to detach it, and then proceed to replace the propeller. 
3. Align the pins on the propeller guard with the corresponding holes, and securely install the guard in place.

Note
You can replace propeller guards with the spare rings for longer flight time. Avoid inserting your fingers into the rotating propellers after replacment.

Remote

FIRST-TIME USE

Flight Preparation

1. Remove the battery from the drone, then charge it with the USB charging cable provided in the box.
2. After fully charging the drone’s battery, securely install it by inserting itinto the drone until you hear a click sound.
3. Insert 3 AAA batteries into the remote and tighten the screw.
4. Attach the phone holder and securely place your device inside. To detach the phone holder, push the detach button on the remote downward while removing the phone holder. 
5. Press and hold the power button for 3s on the drone to power it on, then place it on a flat and level surface. 
6. Press and hold the power button for 3s on the remote to power it on. The drone will automatically pair with the remote. If the pairing fails, power off the drone and remote, then try again. 

Connect the SNAPTAIN FPV App with Your Drone

1. Download and install SNAPTAIN FPV from Google Play™/App Store™ or scan the QR codes below.
   

2. Simply navigate to the WiFi setting of your mobile phone and search for SNAPTAIN-K30-XXXXXX WiFi to connect.

3. Launch the SNAPTAIN FPV app, then tap FUNCTION DISPLAY to enter the main page to see the live preview.

Flight Control

1. Take-off

2. Option 1:
   Unlock the drone by simultaneously pushing the Right Control Stick to the lower left at 45° and the Left Control Stick to the lower right at 45° until the 4 propellers start rotating. Then, push the Left Control Stick forward.

3. Option 2:
   Press and hold the One Key Take-off button for ls.

4. Option 3:
   Place the drone in your palm right side up, then toss it into the air at least 10cm high.

Flight Directions
The default remote mode is Mode 1 (used for manual illustration). To switch the remote mode: with the remote turned off, press and hold the FN button; while holding the FN button, press and hold the button until the remote is turned on.

1. Mode 1
2. Mode2

FUNCTIONS

One Key Take-off and Landing

• Take-off: Place the drone on a flat and level surface without any obstacles then press and hold the button for ls to make it ascend and hover at a height of 3.9ft (1.2m).
  

• • Land: When the drone hovers in the air without any obstacles, press and hold the button for ls to make it descend and land until the propellers stop rotating.
    

Circle Fly
If there are no obstacles within a radius of 5 meters around the drone, press and hold the button for 3s on the remote to make the drone fly in a circular pattern.

Press and hold the button for 3s again to disable this function. To perform this function, the drone must have enough power.

Doodlefly

1. Open the App and navigate to the main page.
2. Tap on the 0la 11 (Doodlefly) icon and adjust the scale by sliding the  scale bar. The default scale is set to 1:1.
3. Use your finger to draw a desired flight path on the blank area of the  screen.
4. The drone will follow the trajectory path without changing its flight height, but the length of the trajectory will vary based on the selected scale .
   

3D Flip
After flying the drone in an obstacle-free area, press the button to activate the 360 flip function. Once activated, use the Right Control Stick to perform flips. Push the stick forward, backward, leftward, or rightward to execute a 360° flip in the corresponding direction.

To perform this function, the drone must have enough power.

Emergency Stop
If an abnormal situation occurs, you can simultaneously press and hold the button and button on the remote for 3 seconds to make an emergency stop.

Please make an emergency stop when the drone’s flight height is below 9.8ft (3m). If the drone’s flight height is above 9.8ft (3m), carefully descend it to a height below 9.8ft (3m) before performing the emergency stop.

Notes

• When this function is activated, the drone’s motor and propellers will stop rotating, causing it to fall from the sky and potentially pose risks of damage. Use this function with caution. * After an emergency stop, if you intend to fly the drone again, please reset the drone.

Throw to Go
Place the drone in your palm right side up, then toss it into the air at least 10cm high. The drone will automatically hover in the air.

Notes
If the lights on the drone flash after a failed Throw to Go, reset the drone before retrying.

Light Mode Switch
Press and hold the button to switch between different light modes. To turn off the lights, simply press and hold the Q button.

FN (Custom Function)

• Press the FN button for the first time: The drone will execute default flight actions. It is recommended to use this feature in an open area without obstacles for safety reasons.
• The drone will execute custom actions. Check the app for more details.

Headless Mode
Launch the app and tap the  button to activate this function. In this mode, the drone will fly following the direction of the Right Control Stick regardless of the position of your drone’s head or tail.

Tip:
The drone camera’s orientation is its “head” position. In headless mode, the direction is defined by the drone’s head orientation at takeoff. Remembering the drone’s head orientation during takeoff will help you navigate accurately in headless mode.

Find Your Drone
When the drone is accidentally lost during flight, simultaneously press and hold the FN button and button on the remote for 3 seconds to try to locate it. In response, the drone will emit rapid beeps. To exit this state, you can either repeat the above operation or briefly press the Power button on the drone.

To perform this function, the drone must be connected to the remote and have enough power.

DRONE’S LIGHTS

BEEPS EXPLANATION

SPECIFICATIONS

Drone

Camera

Remote

FCC

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For Remote:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

For R/C QUADCOPTER:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISEDC Warning:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

For R/C QUADCOPTER:
The device is compliant with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. The minimum distance from body to use the device is 20cm.

For Remote:
The device is compliant with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

support.na@ametasmart.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>