MOUNT-IT MI-6771 Full Motion Single Monitor Desk Mount Instruction Manual
- June 3, 2024
- Mount-It
Table of Contents
MOUNT-IT MI-6771 Full Motion Single Monitor Desk Mount
Please scan this QR code to visit the product page.
HAVE QUESTIONS?
- Monday- Friday from 8:00am – 4:00pm PST
- Support@mount-it.com
- 855-925-5668
- www.mount-it.com
Thank you for choosing Mount-lt!
Read the entire instruction manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings,
please contact
Mount-It! for assistance
CAUTION: Use with products heavier than the rated weights indicated may
result in instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
- Make sure that the supporting surtace will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).
Mount and Accessories
Monitor Mounting Hardware
- Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct desk mounting and monitor mounting hardware suitable for your installation.
- CHOKING HAZARD. Package includes small parts.
- Not for children under 3 years. Adult supervision is required.
- Missing Parts? Call us at 855-925-5668 and we will ship replacement parts free of charge.
DIMENSIONS & WEIGHT CAPACITY
Rated weight capacity is 19.81lbs”.
Caution
Ensure all mounting surfaces are capable of holding the weight of your
Monitor+Mount.
DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR!
INSTALLATION INSTRUCTION
- Step 1: Clamp Installation Option
Clamp Installation Instructions: Open the clamp to be wider than the width of the desk then slide the clamp into place in the desired location. Tighten the clamp back down using 6mm Hex Wrench (#L) until it is secure. Slide the Cable Management Clip (#F) into place as shown.
Grommet Installation Option
* Use 6mm Allen Key (#L) to remove the bolt from the center of Mount Base (#C). This will also detach the lower clamp portion. Store the removed parts to be able to convert the mount to a clamp configuration.
* A grommet hole of 10-60mm is requred for installation. If a grommet hole is not present in your desk surface, use a 3/8” drill bit to create a hole in the desired location.
* Place the Mount Base (#C) over the grommet hole and insert Grommet Bolt (#J) through the desk and connect To grommet Plate (#E) on the underside of the desk. Tighten with 6mm Allen Key (#L) until secure. Slide the Cable Management Clip (#F) into place as shown.
- Step 2: Insert the Vertical Pole
- Use the screwdriver end of 4mm Hex Wrench (#K) to partially loosen the two bolts on the top of the Clamp Base. Do not remove the bolts, stop loosening once bolts are loose enough to allow the pole to be installed.
- Insert the threaded end of the Pole (#H) into the mount base and twist the pole until it is secure.
- Tighten the two bolts back down to secure the pole into place.
- Step 3: Install the Arm Connector
- Attach the Cable Management Clip (#I) to the vertical pole approximately halfway between the base of the pole and the desired location for the Arm Connector.
- Use 6mm Hex Wrench (#L) to partially loosen the bolt on the Arm Connector (#G).
- Slide the Arm Connector onto the vertical pole in the orientation shown, and hold it at the desired height.
- Tighten the bolt back down until it is secure and to fix the arm connector in place
- Step 4: Attach the Swivel Arm
- Using the screwdriver end of 4mm Hex Wrench (#K) partially loosen the bolt on the outer end of the arm connector.
- Insert the Swivel Arm (#B) into the end of the arm connector.
- Tighten the bolt back down to prevent the removal of the swivel arm.
- Step 5: Attach the Spring Arm
- Using the screwdriver end of the 4mm Hex Wrench (#K) partially loosen the bolt on the end of the swivel arm.
- Insert the Spring Arm (#A) into the end of the swivel arm.
- Tighten the bolt back down to prevent the removal of the spring arm.
- Step 6: Attaching the VESA Plate Cable Management
Select the appropriate size mounting bolt (Select one size #M-A or M-B) and washer (#M-C) for your display’s mounting holes and verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to your monitor user manual or contact the monitor manufacturer for sizing information. Attach the VESA Plate using the selected bolts and tighten until secure. Do not overtighten.
- Step 7: Connect the Monitor to the Spring Arm
- Turn the knob on the top of the VESA plate so that it is perpendicular to the monitor and the arrows are pointing to the image of the unlocked lock.
- Slide the monitor and VESA plate into place on the end of the spring arm. Take care to not drop the monitor too quickly before the gas spring tension is adjusted as shown in step 9.
- Turn the knob so that it is parallel to the monitor and the arrows are pointing to the image of the locked lock.
- Step 8: Attaching the VESA Plate Cable Management
- There are covers for the cable management system on each segment of the mount arm. Remove them by sliding the cover away from the center of the mount (do not pull or pry them away from the arm or the cover will be damaged.) Route the cables beneath the covers and slide them back into place.
- **Step 9
**
* To properly balance the arm with monitor mounted, adjust the spring tension using the supplied Allen Key as follows:
* First, position and firmly hold the arm horizontally as shown. Ask for assistance should vou require it.
CAUTION: To avoid damage to monitor or mount, always keep the arm in a
horizontal position while making adjustments. Again, ask for assistance if
required.
CAUTION:
DO NOT over tighten the screws.
Final Adjustments
Note: If the display does not stop at your desired position, tighten the screws as shown.
Note: If the display does not stop at your desired position, tighten the screws as shown.
CUSTOMER SERVICE
- Visit us at www.mount-it.com for product registration and warranty information.
- Our US based customer service team is standing by to answer any questions you have about your Mournt-It! product.
- Available by phone Monday Friday from 8:00am to 4:00pm PST. Chat live with an agent on our website!
- Support@mount-it.com
-
- 925-5668
- www.mount-it.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>