DUSUN DSW-080 Smart Switch User Manual
- June 5, 2024
- Dusun
Table of Contents
- Introduction
- Mechanical Requirement
- Key components
- Basic function
- Electrical Characteristics
- Zigbee RF features
- BT/BLE performance
- Interface
- Environmental adaptability
- EMC
- Reference application
- Installation
- Certification
- Marking, packaging, transportation and storage
- FCC
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DUSUN DSW-080 Smart Switch User Manual
Introduction
Purpose & Description
This is a smart switch for the access control and garage door. It’s with
Zigbee and Bluetooth wireless protocol.
User can easily make your access control intercom and garage door control to
be smart. It can control your access control and garage door remotely.
And this product can also be used for data transmit function, like RS485 (UART
or Modbus) transmit to Zigbee /Bluetooth.
Product Feature Summary
- Average standby current: <100uA
- Average working current: <45mA
- Support Bluetooth 5.2, with external antenna
- Support Zigbee3.0,can connect to gateway
- Support DC power supply and Li battery backup
- 2 channel Relay switch for access control/garage door control and 2 sensor input I/O for status detect
- 2 ports for electric accessories
- UART or RS485 (Modbus )
- Operation temperature: -10~55℃
- Operation humidly:<90%(NON condition)
- Button:2(one for reset function ,and one for pair key )
- LED:1(RGB)
- Antenna: internal PCB antenna (Zigbee)
- Built-in battery :Li battery ,1000mAh
- Battery life : 3months(it’s rechargeable)
- Recharging current: 0.5C
- RTC: support
- Working distance (open field) Zigbee: >100m BLE: >70m
- Outline size:85mm60mm23mm
- IP protection: IP20
- Net weight:~110g
Application
- Intelligent building
- Smart household and home appliances
- Industrial wireless control
- Home automatic
- Garage smart control
- Environment detect
- Data transmission
- Remote control
Hardware block
Mechanical Requirement
Drawings
Outline size
Key components
Some key components are shown in the table below
No. | Part No. | Spec | Manufacturer | Remark |
---|---|---|---|---|
1 | MCU | APM32F030ZET6 | Geehy | |
2 | Zigbee module | DSM-041 | Dusun | |
3 | 485 IC | TP485E | 3PEAK |
Basic function
LED blinking and key description
- Status Indicator:
- Fast flashing: 2Hz,Duty50%;slow flashing: 1Hz,Duty50%.
Indicator| Status| Description
---|---|---
Blue| Off| Device is not powered on
Slow flashing once in 5 seconds| Device is working normally
green| Slow flashing 3 times| Restore factory
Slow flashing| Pair mode
Red| Slow flashing| Low voltage
Fast flashing| Shut down
Always on| Network failure
Note: When the indicator and status lights are working, the power indicator
does not work.
- Short press: key time <200mS
Power-on initialization
When the product is powered on, the Blue indicator flashes slowly for 2 times
and then stays on, and the initialization is successful.
Pairing
After the product is initialized, short press the pairing button once, the
device enters the pairing mode, the distribution Green LED indicator flashes
quickly, and exits the distribution network status directly after the timeout,
the timeout period is 60S.
Restore factory settings
Press the key for more than 30S, the distribution Green LED flashes 3 times,
the device restores the factory settings and enters the pairing state.
Button function
Pairing button:
Short press: when the network is not configured, it enters the network
configuration state; when the network is configured, it does not respond.
Press key time 8~15S, clear network information;
Press the key for more than 30S, restore factory settings;
Reset button: restart device.
Power-on default state setting
After the device is powered off, power on again to set the status of the relay
after power on. The enumerated values are as follows:
None: Power-off memory, after power-on, the relay keeps the state before
power-off.
On: Normally open state; the relay is turned on after power-on again.
Off: Normally closed state, the relay will be disconnected after power-on
again.
Configurable reporting time
The device status reporting time can be set by users according to their own
needs, ranging from 1-64800 seconds, and the default is 60 seconds.
OTA function
The device supports the OTA function, and the device can be upgraded remotely
through the gateway. The OTA function requires a digital signature function,
and programs other than the device cannot be upgraded.
Voltage detection
The product has a built-in lithium battery. When the external power supply is
cut off, it is powered by the built-in battery. When the voltage is detected
to be lower than 3.8V-0.1V, the red LED will flash slowly 3 times, prompting
the user to charge. When the voltage is lower than 3.5V-0.1V, the red LEDs
will flash fast 6 times, and all functions will be turned off
Electrical Characteristics
Absolute Electrical
Parameter | Description | Min | Typ | Max | Unit |
---|---|---|---|---|---|
Ts | Storage temperature | -20 | – | 70 | ℃ |
VBAT | Power-supply voltage | 4.5 | – | 5.5 | V |
Static electricity voltage (human model) | TAMB-25℃ | – | – | 8 | KV |
Static electricity voltage (machine model) | TAMB-25℃ | – | – | 2 | KV |
Normal electrical conditions
Parameter | Description | Min | Typ | Max | Unit |
---|---|---|---|---|---|
Ta | Working temperature | -10 | – | 55 | ℃ |
VCC | Working voltage | 4.75 | 5.0 | 5.25 | V |
VIL | I/O low-level input | – | – | IOVDD*0.3 | V |
VIH | I/O high-level input | IOVDD*0.7 | – | – | V |
VOL | I/O low-level output | – | – | IOVDD*0.2 | V |
VOH | I/O high-level output | IOVDD*0.8 | – | – | V |
Note:5VDC from type C USB; 5~12VDC from intercom connection Port
TX power consumption during constant emission
Working
status
| Rate| Tx Power/receiver| Average Value| Maximum
Value| Unit
---|---|---|---|---|---
Tx| 250Kbps| +20dbm| 200| 206| mA
Tx| 250Kbps| +10dbm| 62| 64| mA
Tx| 250Kbps| 0dbm| 26| 28| mA
Rx| 250Kbps| Constant receiving| 10| 12| mA
Rx| 250Kbps| Constant receiving| 10| 12| mA
RX| 250Kbps| Constant receiving| 10| 12| mA
working current
Working Mode| Working status , Ta=25℃| Average
value| Maximum value| unit
---|---|---|---|---
EZ mode| The product is in EZ mode.| 10| 40| mA
Connected and idle| The product is connected to the network| 14.2| 15| mA
Deep sleep mode| The product in deep sleep mode,| 50| –| uA
Zigbee RF features
Zigbee Basic RF features
Parameter | Description |
---|---|
Frequency band | 2.405~2.480GHz |
Wireless standard | IEEE 802.15.4 |
Data transmission rate | 250Kbps |
Antenna type | PCB antenna with a gain of 1.8dBi, option Ipex |
Zigbee Tx performance
Performance during constant transmission
Parameter | Min. | Typ. | Max. | unit |
---|---|---|---|---|
Maximum output power(250Kbps) | – | 20 | – | dBm |
Minimum output power(250Kbps) | – | -30 | – | dBm |
Output power adjustment step | – | 0.5 | 1 | dBm |
Output spectrum adjacent-channel rejection ratio | – | -31 | – | dBc |
Frequency error | -15 | – | 15 | ppm |
Zigbee Rx performance
Rx sensitivity
Parameter | Min. | Typ. | Max. | unit |
---|---|---|---|---|
PER<8%,RX sensitivity(250Kbps) | -102 | -101 | -99 | dBm |
BT/BLE performance
Transmitter(BLE)
Parameters| min| Typ| max| Unit|
---|---|---|---|---|---
Transmit power| –| 6| –| dBm|
Gain control step size| –| 2| –| dB|
RF power control range| -10| –| +12| dBm
Δ f1avg| 240.8| 241.2| 242| KHz
Δ f2max| 175.7| 182.7| 183.9| KHz
Drift rate| –| 1.5| –| KHz
Offset| –| -4.3| –| KHz
Receiver (BLE)
Parameters | min | Typ | max | Unit |
---|---|---|---|---|
Sensitivity @30.8% PER | – | -94 | – | dBm |
Maximum received signal @30.8% PER | – | 0 | dBm | |
Out-of-band blocking | 30MHz~2000MHz | – | -30 | – |
2003MHz~2399MHz | – | -35 | – | dBm |
2484MHz~3000MHz | – | -35 | – | dBm |
3000MHz~12.5GHz | – | -30 | – | dBm |
Intermodulation | -71 | dBm |
Interface
RS-485
The interface of the product as below, J1 and J2 is for the control for access
control.
Pin No. | J1 | J2 |
---|---|---|
1 | B | B |
2 | A | A |
3 | GND | GND |
4 | VCC | VCC |
RS-232
The interface of the product as below, J1 and J2 is for the control for access
control.
The baud rate is 2400~38400bps, the default is 115200bps;
Start bit: 1bit;
Data bits: 8bits;
Stop bit: 1 bit, 1.5, 2 can be selected, the default is 1 bit
Parity bit: none;
Pin No. | J1 | J2 |
---|---|---|
1 | RxD | RxD |
2 | TxD | TxD |
3 | GND | GND |
4 | VCC | VCC |
Intercom connect
The interface of the product as below, J1 and J2 is for the control for access
control.
IO Level 3.3V
Pin NO. | J1 | J2 |
---|---|---|
1 | GND | GND |
2 | Sensor | Sensor |
3 | NO | NO |
4 | COM | COM |
5 | NC | NC |
6 | VCC | VCC |
Environmental adaptability
Climate and environment adaptability
Carry out the climate and environment adaptability test on the product according to the following table. The state should not change during the test. After the test, it should be able to work normally. After the salt spray test, the surface of the metal parts of the electronic anti-theft lock should not be rusted
Item | Test condition | duration | status |
---|---|---|---|
High temperature | temperature: 55℃±2℃ | 4h | working |
Low temperature | temperature: -10℃±3℃ | 4h | working |
Constant heat and
humidity
| temperature: 40℃±2℃
Relative humidity: 90%±3%
| 48h| working
Salt spray
| Concentration of salt solution: 5%±0.1% Temperature: 35℃±2℃
Mist absorption time: 15 minutes spray every 45 minutes
Salt fog precipitation:1.0mL/(h•80cm²)~2.0ml/(h•80cm²)
|
48h
|
Non-working
Mechanical adaptability
Carry out the mechanical environment adaptability test on the product according to the following table, and it should work normally after the test. The mechanical parts and components in the product are not loose, and the shell is not deformed or damaged.
Item | Test condition | status |
---|---|---|
Sinusoidal vibration | Frequency range: 10Hz~150Hz Acceleration: 5m/s² |
Vibration direction: X, Y, Z three axes Sweep rate: 1oct/min
Number of sweep cycles: 1
| working
Free fall drop| height: 1m Geometric faces: 6
Number of drops on each side: 1
Whether to bring packaging: yes
| on-working
EMC
Electrostatic discharge immunity
The limit of electrostatic discharge immunity should meet the requirements of
test level 3 in GB/T 17626.2-2018. The product should not malfunction during
the test and should be able to work normally after the test.
Electrical fast transient pulse group immunity
The immunity of electrical fast transient pulse group shall meet the
requirements of test level 3 in GB/T 17626.4-2018. The product should not
malfunction during the test, and it should work normally after the test.
Surge (impact) immunity
The surge (impact) immunity shall comply with the requirements of test level 3
in GB/T 17626.5-2019. The product should not malfunction during the test, and
it should work normally after the test.
Reference application
Garden Door control
DSW-080 can connect to the electric garden door control board though wire,
smart control method can be two option ,one is Zigbee for long range control
,one is Bluetooth for local control
Option ①:DSW-080 will send the data to Dusun Zigbee gateway though Zigbee
and Sync the data to the cloud, user can use the access control app on the
mobile phone to control the electric garden door open .
Option ②:Mobile phone with app can scan the Bluetooth signal in the near,
the DSW-080 is always in activity status , the app will be automatic connect
the DSW-080,User can control the garage door by the mobile phone
Remark : After entering the administrator mode, the mobile app can
connect to DSW 080 via Bluetooth, and DSW-080 will send the secret key to the
mobile app DSW-080 will always be in the broadcasting state when it is not
connected. When the user holds the authorized mobile app close to it, it will
connect and exchange the secret key.
Whether to open the door automatically depends on the logic of the mobile app.
Garage Door control
DSW-080 can connect to the garage door control board though wire, smart
control method can be two option, one is Zigbee for long range control, one is
Bluetooth for local control
Option ①:DSW-080 will send the data to Dusun Zigbee gateway though Zigbee and
Sync the data to the cloud, user can use the access control app on the mobile
phone to control the garage door open.
Option ②:Mobile phone with app can scan the Bluetooth signal in the near, the
DSW-080 is always in activity status , the app will be automatic connect the
DSW-080,User can control the garage door by the mobile phone
Remark : After entering the administrator mode, the mobile app can connect to
DSW-080 via Bluetooth, and DSW-080 will send the secret key to the mobile app
DSW-080 will always be in the broadcasting state when it is not connected.
When the user holds the authorized mobile app close to it, it will connect and
exchange the secret key.
Whether to open the door automatically depends on the logic of the mobile app.
Intercom control
Can connect the phone to DSW-080 through a flat cable, and then connect
DSW-080 to the network to realize remote control of the phone and remote real-
time access to the status of the call.
DSW-080 can be set as a Zigbee router, some Zigbee sensor and devices can
connect to it.
Remark :
GND and SENSOR is for detect the action of bell ring , NO and COM is used for
open the door. NC normal not to be used VCC can connect to the power supply of
the intercom, in common , the voltage will be from 5VDC to 12VDC
The circuits and interfaces of different brands of intercom are different, so
needed to confirm which ports are connected correctly.
-
Step 1:Find the GND port
Connect the multimeter and activate the mode to measure DC voltage.
Connect the black wire to the COM terminal of the multimeter and the red wire to the V,Ω,mA.
Test all possible combinations between the terminals of the intercom strip until the multimeter shows the highest positive voltage.
If the voltage is negative, invert the connection of the cables: connect the red where the black and the black where the red.
Connect the DSW-080 GND output to the terminal where the black cable of the multimeter is connected.
Remark :If there is a corresponding logo on the intercom circuit board, generally GND or Common Ground represents GND -
Step 2:Find the Sensor port
Measure DC voltage mode on the multimeter and connect the black wire to GND terminal.
Connect the red lead from the multimeter to each of the terminals on the intercom. It will show constant tension. If, when the doorbell button is pressed, the voltage differential varies markedly, that is the sensor terminal. -
Step 3:Find the COM and NO port
Generally, NO and COM are the two ends of the door open button.
Use the beep of the multimeter to find the terminal that is completely short- circuited to the two ends of the door open button. These two terminal can be used to connect the NO and COM ports of DSW-080.
Remark : If cannot find a terminal that is completely short-circuited to the two ends of the door open button, you can directly connect COM and NO to both ends of the door open button. But in this case you need a soldering iron tool to achieve
If the intercom door open button is a touch type button, you can choose an electric accessory to connect to the J3 interface of DSW-080. This accessory will be described in detail in the instructions for use.
Call function connection (traditional intercom)
Traditional intercom are generally analog microphones. Connect the intercom as shown below:
- Unplug the microphone, then connect the intercom main body and micphone to smart switch respectively.
In this way, smart switch can receive and transmit call audio data from the RJ9 interface, and then use Bluetooth to communicate with the gateway to achieve remote calls.
Call function connection (Digital intercom)
For digital phones, we need to use an accessory (sound pickups), the pickups has a noise reduction microphone and speaker function, supports USB audio protocol, the connection diagram is as follows,
- Connect the output port -Type C of the sound pickups to the power supply port of the smart switch
- Connect the power supply port-USB of the pickup to the 5VDC adapter for the power supply of the pickup and smart switch.
Note: Install the sound pickups as close to the intercom as possible.
Similarly, the smart switch get the audio data of the call from the USB port, and communicates the data with the gateway via Bluetooth to achieve the remote call function.
Door access control
DSW-080 can connect to the door button via wire. Mobile phone with app can
scan the Bluetooth signal in the near, the DSW-080 is always in activity
status, the app will be automatic connect the DSW-080,User can control the
door by the mobile phone
Remark : After entering the administrator mode, the mobile app can connect to
DSW 080 via Bluetooth, and DSW-080 will send the secret key to the mobile app
DSW-080 will always be in the broadcasting state when it is not connected.
When the user holds the authorized mobile app close to it, it will connect and
exchange the secret key.
Whether to open the door automatically depends on the logic of the mobile app.
Thermostat control
Connect the DSW-080 to the thermostat via RS485, and connect DSW-080 to the
gateway via Zigbee Users can remotely control
Installation
3M adhesive stickers
- Step1:Select the adhesive tape to stick to the back of the device, and tear off the adhesive tape on the back of the beacon sensor;
- Step2:Just stick the product to the surface of the object;
Fixing with expansion screw
The screw size:M3*25 Quantity:4pcs
- Step1:Drill holes in the corresponding positions of the wall, and plug the expansion cap into the hole punching positions of the wall;
- Step2:Place the Cradle in the corresponding position and fix it with expansion screws;
- Step3 : Place the product into the cradle.
Extension of the antenna
The antenna can be replaced with an extendable antenna, suitable for areas
with poor RF signal, the antenna wire can be up to 2 meters, and can be
adsorbed on metal materials.
Certification
Products comply with SRRC、CCC、 CE、 RoHS、FCC。
Marking, packaging, transportation and storage
Logo
The packaging box should have the following marks:
- a) Product name, specification model, quantity, volume, quality, warning signs, name and address of the manufacturer;
- b) Trademark name, registered trademark pattern;
- c) Production date: year, month, day;
- d) Adopt the technical standard number.
Packaging
- The packaging materials should be clean, dry, and acid-alkaline should meet the packaging requirements of neutral materials.
- The product is equipped with the required accessories, and is accompanied by product instructions and conformity marks.
- The outer packaging should have sufficient strength to ensure that the product is not damaged or scratched during transportation.
Transportation
The packaged products should be able to ensure the safety in the transportation of cars, trains, airplanes and ships. The transport packaging should meet the requirements for shipping.
Storage
The product should be stored in a warehouse with dry air and no corrosive gas around it, and it should be protected from moisture or rain. Place it in an environment above 20cm from the ground.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance of 20cm from your body.
Hangzhou Roombanker Technology Co., Ltd. Floor 8, building A, Wantong
center,
Tel:86-571-86769027/8 8810480 Hangzhou 310004, china
Website: www.dusuniot.com
www.dusunremotes.com
www.dusunlock.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>