GOLDEN LIGHTING 1081-5P 21 Inch Matte Black Pendant Ceiling Light Instruction Manual
- June 3, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1081-5P 21 Inch Matte Black Pendant Ceiling Light
Instruction Manual
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting.
Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. From the parts bag remove the mounting strap assembly. One
end of the nipple (F) should be attached to the mounting strap (B) with a
washer and a hex nut (C) in place. 2. Attach mounting strap (B) to the
junction box using mounting screws (A) and a screwdriver. Tighten securely.
ASSEMBLING THE FIXTURE
3. Measure to determine the correct length of chain needed for proper hanging
height. If necessary, use a pair of pliers to open and remove any excess
chain. Attach one chain connector (J) to each end of the chain (O). Attach the
chain connector (H) and chain (O) to ring (K) then attach ring (K) to the top
loop (L). Attach the other end of the chain (O) with chain connector (H) to
the canopy loop (D). Close chain connectors to secure. Close ring (K) to
secure the chain (O) and chain connector (H) to the fixture. Feed fixture
wires from post (M) into a top loop (L), through the ring (K), up the chain
(O) (every three links or so) through canopy loop collar (J), canopy loop (D)
and the canopy (I) until the wires come out of canopy (I). Pull the wires
until taut. Thread top loop (L) onto the post (M). Slide canopy loop collar
(J) and canopy (I) down onto the chain/wires.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate the ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of the ground screw (E) onto the
wires and into the mounting bracket/mounting strap. Tuck the wires into the
junction box.
FINISHING THE INSTALLATION
5. Lift canopy (I) up towards the ceiling and over the mounting strap (B) so
that nipple (F) protrudes from the center of the canopy (I). Secure the canopy
(I) by threading on the canopy loop collar (J) and canopy loop (D) over the
nipple (F). Thread until canopy (I) snug against the ceiling. 6. Install light
bulbs (not provided) into sockets (N) within shade (Q) in accordance with the
fixture’s specifications. Arms (P) are adjustable. TAKE CARE THAT THE BULBS DO
NOT TOUCH THE SHADE. Do not exceed the maximum wattage. Your installation is
now complete. Turn on the power and test the fixture.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>