GOLDEN LIGHTING 4855-3LP Galveston 3 Light 35 Wide Linear Chandelier Instruction Manual
- May 15, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 4855-3LP Galveston 3 Light 35 Wide Linear Chandelier
Product Information
Specifications
- Model: 4855-3LP BLK-CLR
- Fixture Type: Pendants & Linear Pendants
- Maximum Wattage: Refer to fixture’s specifications
- Height Above Countertop: At least 30 inches
- Height Above Table: At least 30 inches
- Bottom Clearance from Floor: At least 7.5 feet
Frequently Asked Questions
- How do I identify the fixture’s wires?
- The fixture wires are typically labeled as hot, neutral, and ground. Refer to the provided instructions for specific wire identification.
- What is the recommended height for pendant lighting above a kitchen island?
- For optimal lighting, pendants should hang at least 30 inches above the countertop.
- Can I use dimmers with this lighting fixture?
- Yes, you can enhance your lighting experience by installing dimmers that allow you to control the light output as needed.
- Where can I find replacement parts or customer service for this product?
- Contact the place of purchase for customer service inquiries or to arrange for replacement parts.
Product Dimensions And Installation
Pendants & Linear Pendants Above a Kitchen Island
- Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.
Pendants & Chandeliers Above a Dining Room Table
- Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas
- The bottom should hang at least 7.5 feet from the floor.
- Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
How to Identify the Fixture’s Wires
Product Overview
Parts
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. From the parts bag remove the mounting strap assembly. Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & D) should be attached to mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F).
Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. Remove the canopy and then tighten nuts (C) onto mounting screws (A) to hold the screws in place. 2. Pull the house wire though the center of the mounting strap (B). Place mounting strap (B) over the junction box and secure in place with mounting screws (D). Tighten the screws securely with a screwdriver.
ASSEMBLING THE FIXTURE
Measure to determine the correct number of rods (H) needed for proper hanging height. To shorten the fixture, slide the desired number of excess rods off. To lengthen the fixture, add additional rods. If additional rods are needed, please contact the place of purchase to order more. Feed the fixture wires from posts (I) into rods (H). Pull the wires until taut. 4. Thread the rods together to secure. Secure rods onto the fixture frame by twisting the bottom of the rods (H) onto post (I). Twist the top of the rods (H) into the threads of swivel post. Pull the fixture’s wires through swivel and canopy (F). Trim the wires to the desired length adding at least 8 to 10 inches of wire.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction.
If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (F) up to the ceiling until mounting screws (A) protrude from the holes in the canopy (F). Thread deco nuts (G) onto the exposed threads of mounting screws (A) until snug against the ceiling to secure. Tighten until the canopy (F) is snug against the ceiling. 7. Slide shades (K) over sockets (J) and secure using socket rings (L). Install light bulbs (not included) into sockets (J) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
Contact
Get help, quick tips, and explore curated content
Scan Me
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
- Fb: @GoldenLighting
- Insta: @GLFixtures
- Twitter: @GoldenLighting1
- Pinterest: @GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>