Golden Lighting 0890-3P Alcott 3 Light Taper Candle Pendant Installation Guide

Table of Contents

Golden-Lighting-0890-3P-Alcott-3-Light-Taper-Candle-Pendant-product-
image

Specifications:

Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of island. Fixtures should hang at least 30 inches above the countertop
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open
Areas The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

Installation Tips:

FAQ:

Q: How do I identify the fixture’s wires?
- Fixture Wires: Hot (Neutre/Neutro), Neutral (Neutral/Neutro), Ground (Ground: Copper, Bare Metal, Green, or Transparent Inner Thread)
- House Wires: Hot, Neutral, Ground
Q: Where can I find help and quick tips?
You can visit Lightinginstructions.com for assistance and curated content.
Q: What is the maximum wattage for light bulbs?
Do not exceed the maximum recommended wattage mentioned in the fixture’s specifications.

Thank You for Choosing Us for Your Lighting Needs!

$Golden-Lighting-0890-3P-Alcott-3-Light-Taper-Candle-Pendant- $1$$

Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!

Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic.
Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice.

How to Identify the Fixture’s Wires

For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. From the parts bag remove the mounting strap assembly. One end of nipple (F) should be attached to mounting strap (A) with washer (C) and hex nut (D) in place. The other end should have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. 2. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar should fit snugly onto the canopy loop. Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached.

ASSEMBLING THE FIXTURE

Connect top loop (L) to post (M) of fixture body (N). Pull the wires through top loop (L) until taut. 4. By measuring, determine the correct number of chain links needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. 5. Attach chain connectors (K) to each end of chain (J) before attaching one end of the chain connector/chain to top loop (L). Close the chain connector. Connect the other chain connector (K) to canopy loop (H). 6. Pass the fixture’s wires up through chain (J) (every three links or so). Slide canopy loop collar (I) and canopy (G) onto the chain/wire.

CONNECTING THE WIRES

Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
- Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy (G) in place.
- Install light bulbs (not provided) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.