GOLDEN LIGHTING 3164-1W BCB-HWG Aenon 7 Inch Wall Sconce Instruction Manual
- June 1, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3164-1W BCB-HWG Aenon 7 Inch Wall Sconce
Product Specifications:
- Height: 8 feet
- Width: 30 inches
- Recommended Hanging Height: 30 inches above countertop
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island:
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of the island. Fixtures should hang at least 30 inches above the countertop.
Colgantes y colgantes lineales sobre una isla de cocina:
Centre un colgante lineal sobre la isla. Si cuelga colgantes, use un colgante por cada 24 pulgadas de isla. Los accesorios deben colgar al menos 30 pulgadas por encima de la encimera.
Pendants & Chandeliers Above a Dining Room Table:
Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas:
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
Tips for Best Lighting:
To ensure the best lighting in your space, remember to layer your lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs. Install lights with dimmers for adjustable light output.
Looking for More Options?
Browse our site for coordinating lights and expert lighting advice at www.GoldenLighting.com.
FAQ
Q: What should be the clearance height for pendants above a kitchen island?
A: Pendants above a kitchen island should hang at least 30 inches above the countertop.
Q: How do I identify the fixture’s wires for installation?
A: The fixture wires typically include hot, neutral, and ground wires. Match them with the corresponding house wires to connect properly.
Thank You for Choosing Golden Lighting for Your Lighting Needs!
-
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop. -
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table. -
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power
at the circuit breaker and remove old fixture from wall, including the old
mounting strap. PLEASE NOTE: This fixture may be mounted with the sockets and
glass facing up or down. Please decide how you would like the fixture to be
hung and turn the backplate accordingly. 1. Mounting strap (A) contains
several pairs of threaded holes and two sets of mounting screws (B & C). You
may need to tighten the hex nuts that hold mounting screws (B) in place. 2.
Place mounting strap (A) up to your junction box. Place backplate (D) over the
mounting strap (A) lining up mounting screws (B) with the holes in backplate
(D). This will allow you to ensure that you are hanging the fixture straight.
3. Pull the house wires from the junction box and through the center of
mounting strap (A). Secure mounting strap (A) to the junction box with
mounting screws (C) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
5. Place backplate (D) over mounting strap (A) so that mounting screws (B)
protrude through the holes in backplate (D). Secure the backplate to the
mounting strap with decorative nuts (F). Twist until the backplate of the
fixture is snug against the wall. 6. Attach glass panel (H) and iron plate (I)
to the fixture by aligning holes and holding against screws (G) found on the
fixture arms until screws protrude out from the holes in the glass panel (H)
and iron plate (I). Secure glass panel (H) and iron plate (I) to fixture arms
using deco nuts (F). Thread until secure. 7. Install light bulb (not included)
into socket
(J) in accordance with the fixture’s specifications. Do not exceed maximum
recommended wattage. Your installation is now complete. Turn on the power