BLAUPUNKT CJ5010 Jigsaw Instruction Manual

BLAUPUNKT CJ5010 Jigsaw

Product Information

• Product Name: CJ5010
• Product Type: Wyrzynarka Jigsaw (Jigsaw Saw) Product
• Model: CJ5010 Description of Equipment:

1. Debris blower lock switch
2. Handle
3. Switch lock
4. Vent
5. Chip blow out
6. ON/OFF switch of the device
7. Pan guard
8. Foot
9. Undercut degree adjustment
10. Battery charge indicator
11. State of charge indicator button
12. Battery pack latch release button

Operating the Device:

1. Insert the plug into the wall socket and then press the button (5) to turn the device on.
2. The tool features a debris blower at the cutting area to remove debris from the workpiece during operation. Start the debris blower by moving the switch (1) to the blower mode.
3. To set the undercutting, select the movement of the blade pendulum to the material that will be cut.

Blade Installation:

1. Make sure the device is disconnected from the power source.
2. The device is equipped with a rapid blade installation system (SDS).
3. Turn the SDS chuck.
4. Place the blade in the chuck.
5. Release the SDS clamping ring.
6. When replacing the blade, make sure that:
   • `The blade holder is free from other materials.
   • Always check that the blade is securely clamped before use.

Blade Removal:

1. Remember to wait after work because the blade may be hot.

2. Make sure the device is disconnected from the power source.

3. otate the saw blade chuck SDS ring and remove the blade from the chuck.
   Installing the Guide:

4. Make sure the device is disconnected from the power source.

5. Place the guide in front of the foot in the holes provided for this purpose.

6. Set the guide size you need to achieve and then tighten the fixing screws. Cleaning and Maintenance:

  * Follow the instructions in the user manual for cleaning and maintenance of the device.

Product Usage Instructions:

1. Before using the CJ5010, read the user manual for proper instructions and safety precautions.
2. Wear safety glasses to protect your eyes from debris.
3. Use ear protection to protect your ears from the noise produced by the device.
4. Wear protective gloves to protect your hands during operation.
5. Wear protective clothing to protect your body from any potential hazards.
6. Wear a protective mask to protect yourself from dust and particles.
7. Use respiratory protection if necessary.
8. Make sure the device is disconnected from the power source before performing any blade installation or removal.
9. Always check that the blade is securely clamped before use.
10. Start the debris blower by moving the switch to the blower mode before operating the device.
11. Set the undercutting according to the material that will be cut.
12. Follow the instructions in the user manual for installing the guide if needed.
13. Follow the instructions in the user manual for cleaning and maintenance of the device.
14. If any repairs are required, contact the manufacturer or an authorized service center.
15. Observe the specified noise levels and take necessary precautions to protect yourself from excessive noise exposure.
    Note: The provided text contains some sections in Polish, which may need to be translated for complete understanding of all information and instructions.

IMPORTANT INFORMATION

To achieve the highest satisfaction, enjoy the product’s performance and learn about all its features and functions, please read this manual before using the product.
Before using the device, read the Operating Instructions and comply to its contents. The manufacturer shall not be liable for any damage caused by the use of the device other than for its intended purpose or by improper handling.
Keep these Operating Instructions for future reference.

• This device is for domestic use only. Do not use for any other purposes.
• The device should only be connected to an socket with values corresponding to the values on the rating label.
• It is necessary to check, if total current consumption of all devices plugged into the wall outlet does not exceed the fuse in the circuit.
• If you are using an extension cord, make sure that the total power consumption of the equipment plugged into the extension cord does not exceed the extension cord power rating. Extension cords should be arranged in such a way as to avoid tripping hazards.
• Do not let cord hang over edge of counter, or touch any hot surface.
• The device is not designed to be controlled via an external timer, separate remote control, or other equipment that can turn the device on automatically.
• Before maintenance work always disconnect the unit from the power supply.
• When unplugging the power cord from electrical outlet, hold it by the plug only and remove the plug carefully. Never pull the cable as it may cause damage to the plug or power cord. Damage to the power cord or plug can lead to an electrocution hazard.
• Never leave the product connected to the power source without supervision.
• Never put the power cable, the plug or the whole device into the water or any other liquids.
• The device should be cleaned regularly complying with the recommendations described in the section on cleaning and maintenance.
• Do not place the device near sources of heat, flame, an electric heating element or a hot oven. Do not place on any other device.
• The appliance must not be used by children. Keep the appliance and its cord out of the reach of children.
• The appliance may be used by individuals with limited physical, sensory or mental capability as well as those without knowledge of or previous experience in the use of similar appliances, provided such individuals are supervised or instructed with regard to the safe operation of the appliance and are informed about the potential hazards.
• Additional precautions should be taken when using this device in the presence of children or pets. Do not allow children to play with the device.
• Never use the product close to combustibles.
• Never expose the product to atmospheric conditions such as direct sun light or rain, etc… Never use the product in humid conditions (like bathroom or camping house).
• The power cable should be periodically checked for damage. If the power cable is damaged the product should be taken to a professional service location to be fixed or replaced to prevent any hazards from arising.
• Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product by yourself as it can lead to electric shock. Always return the damaged device to a professional service in order to repair it. All the repairs should only be performed by authorized service professionals. Any attempted unauthorised repairs performed can be a hazard to the user.
• Only Original accessories should be used, as well as accessories recommended by the manufacturer. Using accessories which are not recommended by the manufacturer may result in damage of the device and may render the device unsafe for use.
• Keep your workplace tidy and well lit.
• Disorder and insufficient lighting lead to accidents.
• Do not use power tools in explosive atmospheres, i.e. in the presence of flammable liquids, gases or dust.
• A moment of carelessness may cause losing control of your tool.
• If it is possible to fit power tools for dust extraction or collection, check that they are fitted and working correctly. Using such power tools reduces the risk posed by the presence of dust.
• Do not lean out too far when working with your power tool. Maintain a stable posture and balance. This allows you to keep better control of your power tool in unforeseen situations.
• Avoid starting the power tool unintentionally. Make sure the power switch is in the OFF position before connecting the power tool to the mains. Carrying a power tool with your finger on its trigger or plugging in a power tool after switching it on can lead to accidents.
• Wear appropriate clothing. Do not work in loose clothing and do not wear jewellery while working. Keep your hair, clothing and gloves away from moving parts. The moving parts of a power tool can catch and pull in loose pieces of clothing, jewellery or long hair.
• Remove any spanners or tools from the power tool before starting it. A tool or spanner still connected to the rotating part of the power tool may cause personal injury.
• Be careful when working with power tools, concentrate on your work and use common sense. Do not use a power tool when tired or under the influence of drugs, alcohol or medication. Even a moment of carelessness while working with a power tool can lead to a serious accident.
• Keep children away from the work area and DO NOT allow children to pull on the power cord – this can cause serious injury.
• Before making any adjustments, changing accessories or storing the power tool, move the switch to the off position to disconnect the power tool from the power supply. Such precautions reduce the risk of accidentally starting the power tool.
• Ensure that the vents are free from debris.
• The device may only be used in a dry, well-lit environment.
• This tool should not be used by anyone under the age of 16.
• When carrying out work where the tool or clamping attachment could come into contact with concealed electric wires, hold the power tool only by insulated surfaces. Contact of the tool or clamping attachment with a live electrical conductor may cause voltage to be transmitted to non- insulated metal parts of the power tool, causing a risk of electric shock.
• Loss of control of the power tool may result in personal injury.
• Hold the power tool firmly. High reaction torques may periodically occur while tightening and loosening screws and bolts.
• Secure the workpiece. Clamping the workpiece in a clamping device or vice is safer than holding it by hand.
• Make sure that the power tool is fully stopped before putting it down.
• In the event of work tool jamming, switch off the power tool immediately. A jammed tool can lead to a high-reaction torque causing a kickback.
• Wear hearing protection while impact drilling .
• Use only clean and sharp cutting tools (such as drill bits). Using blunted tools reduces work efficiency and increases the risk of accidents.
• Select the operating mode and the work tool according to the type of the workpiece.
• Check the condition of the dust cover. In the event of damage, replace it with a new one or send the device to a professional service centre.
• Working on some materials generates dust that may pose health risks, cause allergic reactions or respiratory diseases, and contribute to developing cancer. Ensure good ventilation at the work station and use dust masks with an appropriate protection rating.
• Materials containing asbestos must be handled by properly trained personnel.
• The machine can only be used in indoors with a functioning ventilation system.
• Take special care when changing the work tool. It can be very hot and/or sharp immediately after use. It is recommended to use protective gloves.
• Use only sharp blades in perfect condition. Condition to replace: cracked, distorted or blunt.
• Make sure the foot adjustment screws are tightened before resuming work.
• Choose the right blade for the material, stroke frequency and pendulum.
• Make sure that the saw blade does not touch other objects when the tool is switched on.
• Hold the device by the insulated handle as the blade may run over the electrical wires.
• Only charge the batteries in chargers specified by the manufacturer. There is a danger of fire if a charger designed for specific battery types is not used as intended.
• The battery should only be used in the manufacturer’s equipment. This is the only way to protect the battery from dangerous overloading.
• Only use the power tool with the correct batteries. The use of other batteries could cause a risk of personal injury and a fire hazard.
• The battery can be damaged by sharp objects such as nails or screwdrivers as well as external forces. The battery may then short circuit internally and burn out, explode or overheat.
• When not in use, keep the battery away from metal items such as paper clips, coins, keys, nails, screws or other small metal objects that could short-circuit the battery terminals. A short circuit between the battery terminals can cause burns or a fire.
• Vapours may occur if the battery is damaged or not used as intended. The battery may catch fire or explode. Provide access to fresh air or contact your doctor in the event of any discomfort. Vapours may irritate the respiratory tract.
• Do not open the battery. Short-circuit hazard.
• Wait until the power tool stops moving before putting it down. The work tool may jam and lead to a loss of control of the power tool.
• Storing or using the battery in unsuitable conditions can cause electrolyte leakage. Avoid contact with the electrolyte, and flush the skin with water in the event of accidental contact. Additionally, seek medical advice if the electrolyte comes into contact with the eyes. Electrolyte leaking from the battery can cause skin irritation or burns.
• After finishing work, always wait for the device to come to complete stop.
• Do not turn off the power tool during operation, it may get stuck and you may lose control of the device if you try to switch it on again.
• Do not saw objects with a larger diameter/thickness than the length of the blade.
• Use the blades according to their intended use, and before cutting the material, inspect them carefully for foreign objects such as nails or screws.

Charger and battery pack safety instructions
To connect the battery pack for charging, insert the battery pack into the charger dock and plug the charger to a power source.

• Keep the charger away from rain and moisture. The charger may only be used indoors.
• Keep the charger clean.
• Do not operate the charger on readily combustible objects and surfaces (e.g. paper) or areas with flammable/explosive atmospheres.
• Always ensure adequate ventilation when charging; fumes or battery acid can be released from the battery pack if the latter is compromised by poor handling or damage.
• When charging is complete, unplug the charger from the power source. Do not leave it connected to a power source for longer than necessary.
• Store and charge the battery pack in a dry place and make sure it will not be flooded by water.
• Keep the battery pack terminals clean and free of dirt.
• Protect the battery pack from shocks and moisture; never open the battery pack or expose it to any damage.
  The battery pack charge level can be displayed with the number of charge indicator LEDs by pressing the state of charge indicator button on the pack; if required, charge the battery pack for as long as required to reach the desired charge level and the expected operating time of the cordless power tool.

Kickback:
The kickback is sudden and uncontrollable, the device reacts to the jamming or blockage of the cutting device. Jamming or blocking results in a sudden jerk, in the direction opposite to the rotation of the disc.
Kickback is the result of not reading the safety instruction.
To avoid kickback, follow the safety instructions and use methods to prevent it

Methods to prevent kickback.

• a) Hold the device by the two handles firmly and securely. Always use the additional handle. – The operator can control the torque and the resultant kickback forces if appropriate precautions are taken.
• b) Keep hands away from the cutting part of the device. CAUTION: The device may injure the user if used improperly.
• c) The user should stand in such a position that, in the event of a kickback, they are not within reach of the grinder disc.

SYMBOLS

• The following symbols may appear in the operating instructions or on the tool’s nameplate.
• These signs contain important information about the product and instructions on how to use it.

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2012/19/EU. Please inform yourself about the local separate collection system for electrical and electronic products. Used appliance should be delivered to the dedicated collecting points due to hazardous components, which may affect the environment. Do not dispose this appliance in the common waste bin.

Your products is designed a manufactured with high quality materials and components, which can be recycled and reused.

WEAR PERSONAL PROTECTIVE EQUIPMENT

• Wear safety glasses according to En166
• Use protective masks in accordance with En149
• Use other types of proper personal protective equipment, depending on the type of work involved.

Description of equipment

1. Debris blower lock switch
2. Handle
3. Switch lock
4. Vent
5. Chip blow out
6. ON/OFF switch of the device
7. Pan guard
8. Foot
9. Undercut degree adjustment
10. Battery charge indicator
11. State of charge indicator button
12. Battery pack latch release button

Storage

Store cordless tools in a dry place and out of the reach of children. For safety concerns, remove the battery pack from the cordless tool before storage. When left connected to a cordless tool, the battery pack is drained faster. Protect the battery pack and power tools from frost, high temperatures, moisture and water.
Do not attempt to repair a failed battery pack. Only the original manufacturer or an authorised service may repair the battery pack.
Recharge the battery packs using only the chargers specified by the manufacturer.
Storage or operation of the battery pack in unsuitable conditions may result in a battery acid leak. Never attempt to use a damaged or modified battery pack. Damaged or modified battery packs may cause unpredictable effects during operation, resulting in health hazards. Keep the battery pack away from open flames and high temperature. If exposed to fire or temperatures above 130°C, the battery pack may explode.

Installing the battery pack

Tip: Using a battery pack incompatible with the power tool may result in abnormal performance or failure of the power tool.
Insert the battery pack into the handle until the battery pack latch clicks (the battery pack should be flush with the receptacle edges on the power tool).

Blade installation:

Make sure the device is disconnected from the power source.
The device is equipped with a rapid blade installation system (SDS). Turn the SDS chuck.
Place the blade in the chuck.
Release the SDS clamping ring.
When replacing the blade make sure that:
The blade holder is free from other materials
Always check that the blade is securely clamped before use.

Blade removal:
Remember to wait after work because the blade may be hot. Make sure the device is disconnected from the power source. Rotate the saw blade chuck SDS ring
and remove the blade from the chuck.

Operating the device

1. Insert the plug into the wall socked and then press the button (5) to turn the device on

2. The tool features a debris blower at the cutting area to remove debris from the workpiece during operation. Start the debris blower by moving the switch (1) to the blower mode.

3. To set the undercutting, select the movement of the blade pendulum to the material that will be worked on. Adjustment in the range of 0-3 is possible, with the knob in mode 0, the undercutting is disabled, and in mode 3 the undercutting is at the top range. The undercutting is used for faster and easier cutting of materials.
   Do not cut hard materials such as metal in the undercutting mode.

4. The machine allows cutting at an angle 45 . To cut at an angle:
   Make sure the device is disconnected from the power source.
   Loosen the fixing screws at the bottom of the foot until the foot can be extended, set the position you need.
   Move the foot to the position you want to get.
   Tighten the fixing screws.

INSTALLING THE GUIDE

Make sure the device is disconnected from the power source.
Place the guide in the front of the foot in the holes provided for this purpose. Set the guide size you need to achieve and then tighten the fixing screws.

CLEANING AND MAINTENANCE

Before cleaning and maintenance, make sure the device is disconnected from the power source. Keep the ventilation apertures (air inlets and outlets) of the device free of dirt. Wipe the device with a dry cloth or blow it with compressed air. Keep the work tool chuck free of dust. It is recommended to clean the device after each use. Do not immerse in water or other liquids. Do not use aggressive cleaning agents or solvents.

Noise
Typical A-weighted noise level measured in accordance with ISO/TR 11688-1:

• Sound pressure level (LpA): 77.6 dB (A) ; LWA: 88.60 dB (A)
• Measurement uncertainty (K): 5.0 dB (A) ; KWA: 5.0 dB (A)
• Noise level during operation may exceed: 88.60 dB (A).
  Wear hearing protection!

Vibrations
Total vibration value measured in accordance with CR1030-1:

• Vibration emission: ah, B =12.13 m/s²
• Measurement uncertainty (K) : 2.5 m/s² ; Km=1.5 m/s² ; KB=1.5 m/s²
• Permissible Operating Time: 15 minutes of operation, 30 minutes off.
  The declared vibrations has been measured according to the standard test method and can be used to compare tools.
  The declared vibrations can also be used in the initial exposure assessment.

Cordless Jigsaw

• Voltage: 18 V
• No-load speed: 0-2700 rpm
• Stroke: 20 mm
• Bevel angle adjustment range: 0° to 45°
• SDS tool-free blade change system
• Pendulum settings: 0-3
• Dust extraction
• Steel shoe
• LED work light
• Battery type: 18 V Li-Ion; BP1840 4.0 Ah recommended (not included)
• Accessories: 1 x wood saw blade, 1 x metal saw blade, 1 x dust extraction adapter, 1 x guide rule
• Dimensions: 23 x 7.5 x 20.5 cm
• Weight: 1.7Kg

DECLARATION OF CONFORMITY

Competence Center

2N-Everpol Sp. z o.o.
ul. Pulawska 403A
02-801 Warsaw, Poland
phone: + 48 22 688 08 00
e-mail: info@everpol.pl
www.blaupunkt.com
In case of questions or problems please contact our service.
Tel. 00 48 22 688 08 33
Email: tools@blaupunkt.pl

All rights reserved. All brand names are registered trademarks of their\ respective owners. Specifications are subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>