GOLDEN LIGHTING 3160-3P Calla 18 Inch Large Pendant Instruction Manual
- June 1, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3160-3P Calla 18 Inch Large Pendant
Product Specifications
- Model: 3160-3P NB-HWG
- Height: 8′
- Width: 30
- Length: 5’9
- Weight: 36 lbs
Product Usage Instructions
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants,use one pendant
for every 24 inches of island. Fixtures should hang at least 30 inches above
the countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30 inches above the table. Use a fixture that is
12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
Layered Lighting Tips:
To ensure the best lighting in your space, layer your lighting with task and
ambient lighting. Coordinating fixtures like sconces,flush mounts, and
pendants can help meet your lighting needs.
Install lights with dimmers for control over light output.
Assembly Instructions: 3160-3P
- Preparing for Installation
- Assembling the Fixture
- Connecting the Wires
- Finishing the Installation
FAQ:
Q: How do I identify the fixture’s wires?
Fixture Wires: Hot (Neutre/Neutro), Neutral (Neutre/Neutro), Ground (Cable De Tierra: Copper, Bare Metal,Green, or Transparent Inner Thread)
House Wires: Hot, Neutral, Ground
Q: Where can I get help or additional information?
You can visit our website at GoldenLighting.com for quick tips, curated
content, and assembly instructions.
Q: What if I need replacement parts?
Contact the place of purchase for customer service and to arrange for
replacement parts.
Thank You for Choosing Golden Lighting for Your Lighting Needs!
DIMENSION
-
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop. -
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table. -
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Assembly Instructions
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- WiresNeutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
-
From the parts bag remove the mounting strap (A) assembly. One end of the nipple (F) should be attached to the mounting strap (A) with washer (C) and hex nut (D) in place. The other end should have a canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop (H) to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar (I) should fit snugly onto the canopy loop (H). Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE -
Lock the nipple (P) joint into the movable head (O). Feed the fixture wires from nipple (P) through head (O) and through top loop (L). Secure top loop (L) onto nipple (N). Pull the wires until taut. Measure to determine the correct length of chain needed for proper hanging height. If necessary, use a pair
of pliers to open and remove any excess chain. Attach one chain connector (K) to each end of chain (J). Attach one end of the chain connector/chain to top loop (L). Connect the other chain connector (K) to the canopy loop (H). Close the chain connectors (K) to secure. Feed the fixture’s wires up through the chain (J) (every three links or so), pulling the wires until tant gently slide canopy loop collar (I) and canopy (G) down onto the chain/wires. Trim excess wires leaving about 8 to 10 inches for later.
CONNECTING THE WIRES -
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION -
Push canopy (G) up to the ceiling and slide canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto canopy loop (H) to secure canopy in place until snug against the ceiling. Attach glass panels (R) and metal washers (S) to the fixture by aligning holes and holding against screws (Q) found on the fixture arms until screws (Q) protrude out from the holes in the glass panels (R) and metal washers (S). Secure glass panel (R) and metal washer (S) to fixture arms using deco nuts (T). Adjust the glass to horizontal and vertical. Install light bulbs (not provided) into sockets (U) in accordance with the fixture’s specifications. Do not exceed the maximum wattage. Your installation is now complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>