GOLDEN LIGHTING 6805-6SF BLK-NR Everly 6 Light Semi Flush Drum Ceiling Fixture Instruction Manual
- June 1, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 6805-6SF BLK-NR Everly 6 Light Semi Flush Drum Ceiling
Fixture
Product Specifications:
- Model: 6805-6/6805-6SF
- Voltage: 120V
- Height: 8′ – 13′
- Width: 30″ – 38″
- Maximum Power: Not specified
Pendants & Linear Pendants Above a Kitchen Island:
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24 inches of the island. Fixtures should hang at least 30 inches
above the countertop.
Pendants & Chandeliers Above a Dining Room Table:
Fixtures should stay at least 30 inches above the table. Use a fixture that is
12 inches narrower than the width of the table.
Pendants and Chandeliers in Open Areas:
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
Layered Lighting
To ensure the best lighting in your space, layer your lighting for task and
ambient lighting. Coordinate fixtures like sconces, flush mounts, and
pendants. Install lights with dimmers for light output control.
Installation Tips
Browse our site for coordinating lights and expert lighting advice. Contact
Customer Service for replacement parts if needed.
Frequently Asked Questions (FAQ):
How do I identify the fixture’s wires?
Fixture Wires: Hot (Neutre/Neutro), Neutral (Neutre/Neutro), Ground
(Cable De Tierra: Copper, Bare Metal, Green, or Transparent Inner Thread)
Thank You for Choosing Us for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendentifs et pendentifs linéaires au-dessus d’un îlot de cuisine Centrez un
pendentif linéaire sur l’île. Si des pendentifs suspendus, utilisez un
pendentif pour chaque 24 po d’îlot. Les luminaires doivent être suspendus à au
moins 30 po au-dessus du comptoir.
Colgantes y colgantes lineales sobre una isla de cocina
Centre un colgante lineal sobre la isla. Si cuelga colgantes, use un colgante
por cada 24″ de isla. Los accesorios deben colgar al menos 30″ por encima de
la encimera.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice.
Assembly Instructions
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread 
Assembly Instructions
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power
at the circuit breaker and remove old fixture from wall, including the old
mounting strap. THIS FIXTURE CAN BE INSTALLED AS A CHANDELIER
OR AS A SEMI-FLUSH. FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED “(1)”. 1. Remove mounting strap (A) assembly from the parts bag. One end of nipple (F) should be attached to mounting strap (A) with hex nut (D) in place. The other end should have canopy loop (H) attached. Attach mounting strap (A) to the junction box using mounting screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test the height. Approximately half of the canopy loop’s exterior threads should be exposed, and the canopy loop collar should fit snugly onto the canopy loop. Remove canopy (G) and adjust the height of nipple (F) and canopy loop (H) until the desired height is reached. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED “(2)”. 1. Find the circular mounting strap (B) and canopy referenced on the diagram “(2)”, it should have several holes for two sets of mounting screws (A & D). Find these mounting screws and align the mounting strap (B) with the holes on your junction box. Insert screws (A) so they protrude from the mounting strap (B). Use hex nuts (C) to hold mounting screws (A) in place.
ASSEMBLING THE FIXTURE
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED
“(1)” 2. Chandelier Installation: Refer to “View 1”, feed fixture wire through
the small cover (M) and top loop (L). Attach the top loop (L) to the nipple
(N). Thread the column (Q) to the bottom nipple (T) to attach the column to
the cluster of lights. Thread the remaining end of the column (Q) into the
connector (P). Connect the shade to the fixture by sliding inner shade (V)
into the outer shade and attaching the small hook (U) onto the small ring (O)
at the top. Attach chain connectors (K) to each end of chain (J) before
attaching one end of the chain connector and chain to top loop (L) and the
other end to the canopy loop (H). Close the chain connectors to secure. Feed
the fixture’s wires up through the chain (J) (every three links or so). Pull
the wires until taut. Gently slide canopy loop collar (I) and canopy (G) down
onto the chain and wires. Connect the shade to the fixture by sliding inner
shade (V) into the outer shade and attaching the small hook (U) onto the small
ring (O) at the top. FOR SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED
“(2)”. 2. Feed the fixture wires from nipple (N) through the canopy (G). Trim
the wires with 8 to 10 inches of wire remaining. Thread the column (Q) to the
bottom nipple (T) to attach the column to the cluster of lights. Thread the
remaining end of the column (Q) into the connector (P). Connect the shade to
the fixture by sliding inner shade (V) into the outer shade and attaching the
small hook (U) onto the small ring (O) at the top. Secure mounting strap (B)
to the junction box using mounting screws (D). Tighten the screws securely.
CONNECTING THE WIRES
3. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
FOR CHANDELIER INSTALLATION REFER TO THE DIAGRAM LABELED
“(1)” 4. Push canopy (G) up to the ceiling and slide canopy loop collar (I) up
beneath the canopy (G). Tightly thread canopy loop collar (I) onto canopy loop
(H) to secure canopy (G) in place. Slide candle sleeves (S) over sockets.
Install light bulbs (not included) in accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage. Your
installation is now complete. Turn on the power and test your fixture. FOR
SEMI-FLUSH INSTALLATION REFER TO THE DIAGRAM LABELED “(2)”. 4. Push canopy (G)
up to the ceiling and tightly thread nuts (I) onto the exposed threads of
mounting screws (A) on mounting strap (B). Slide candle sleeves (S) over
sockets. Install light bulbs (not included) in accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage. Your
installation is now complete. Turn on the power and test your fixture.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>