GOLDEN LIGHTING 7316-OSF Bartlett 1 Light Installation Guide

: June 3, 2024
: GOLDEN LIGHTING

Table of Contents

7316-OSF Bartlett 1 Light
Assembly Instructions:
CONNECTING THE WIRES
FINISHING THE INSTALLATION
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Thank You for Choosing Golden Lighting for Your Lighting Needs!

7316-OSF Bartlett 1 Light

Pendants & Linear Pendants Above a Kitchen Island Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.

Pendants & Chandeliers Above a Dining Room Table Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.v

Pendants and Chandeliers in Open Areas The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Assembly Instructions: 7316-OSF
How to Identify the Fixture’s Wires

Hot: Smooth, Black, or Transparent with Black Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content

https://qrco.de/bbv8UC GOLDEN LIGHTING 7316-OSF Bartlett 1 Light - fig
3

For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:

All installation work should be done by accredited professional.
Shut off power supply at fuse or circuit breaker!
Use only the specified bulbs. Do not exceed the maximum wattage!

Assembly Instructions:

PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
(INDOOR/OUTDOOR FIXTURE – IF INSTALLED OUTDOORS, MUST BE PLACED UNDER
A COVERED AREA)

From the parts bag remove the mounting strap assembly.
Mounting strap (B) contains holes. Two sets of mounting screws (A & D) should be attached to the mounting strap (B). You may need to tighten nuts (C) that hold
mounting screws (A) in place. Place mounting strap (B) over the junction box so that mounting screws (A) are vertical, and in alignment with the locations of the holes on the canopy (F).
Pull house wires through the center of the mounting strap (B). Secure mounting strap (B) to the junction box with mounting screws (D) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.

CONNECTING THE WIRES

Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION

Lift canopy (F) up to the ceiling over mounting strap (B) until mounting screws (A) protrude from canopy (F). Thread deco nuts (G) onto the exposed threads of mounting screws (A). 5. Lift shade (J) over a socket (H) and secure in place using socket ring (I). Install a light bulb (not included) into the socket (H) in accordance
with the fixture’s specifications. Do not exceed the maximum recommended wattage. Place iron cage (K) into the iron cover ring (L). Lift both iron cage (K) and iron cover ring (L) up to the shade (J) and secure together the using screws (M). Thread screws (M) until secure. Your installation is complete. Turn on the power and test the fixture.

Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
GoldenLighting.com
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting