GOLDEN LIGHTING 2073-OFM Smyth 2 Light 13 Wide Flush Mount Outdoor Ceiling Fixture Instruction Manual

GOLDEN LIGHTING 2073-OFM Smyth 2 Light 13 Wide Flush Mount Outdoor

Ceiling Fixture

Specifications:

• Model : 2073-OFM
• Height : 8 feet
• Width : 30 inches
• Weight : 5.9 pounds

Product Usage Instructions

• Pendants & Linear Pendants Above a Kitchen Island:
  Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of the island. Fixtures should hang at least 30 inches above the countertop.

• Pendants & Chandeliers Above a Dining Room Table:
  Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table.

• Pendants and Chandeliers in Open Areas:
  The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

  • We appreciate your business and hope you love your new light! Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
  • Get function and style! Browse our site for coordinating lights and expert lighting advice.

How to Identify the Fixture’s Wires:

Fixture Wires:

• Hot
• Neutral
• Ground

House Wires:

• Hot
• Neutral
• Ground: Copper, Bare Metal, Green, or Transparent Inner
  Thread

Assembly Instructions:

PREPARING FOR INSTALLATION:
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.

CONNECTING THE WIRES:
FINISHING THE INSTALLATION:

1. Lift canopy (F) up over mounting strap (B) so that mounting screws (A) protrude from the holes in the canopy (F).
2. Thread deco nuts (G) onto the exposed threads of mounting screws (A) until the canopy (F) is secure and snug against the ceiling.
3. Install light bulbs (not provided) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage.
4. Thread rod (I) to post (H) until secure. Lift glass shade (J) up to the canopy (F) until rod (I) protrudes from the hole in the glass shade (J).
5. Secure glass shade (J) in place using washer (K), hex nut (L), cap (M), and finial (N) on the exposed threads of rod (I) in the order shown in the diagram. Tighten until secure.
6. After installing the fixture, apply a clear silicone rubber caulking to seal the gap between the enclosure and the mounting surface.
7. Your installation is complete. Turn on the power and test the fixture.

FAQ :

1. Q: How do I choose the right pendant or chandelier size for my space?
   A: For a dining room table, ensure that the fixture stays at least 30 inches above the table and is about 12 inches narrower than the width of the table. For kitchen islands, center a linear pendant or use one pendant for every 24 inches of island, hanging them at least 30 inches above the countertop.

2. Q: How do I ensure proper clearance for open areas?
   A: Pendants and chandeliers in open areas should hang at least 7.5 feet from the floor to allow clearance for any opening doors.

3. Q: Can I use dimmers with these fixtures?
   A: Yes, it is recommended to install the lights with dimmers that allow you to control the level of light output at any given moment.

Thank You for Choosing Us for Your Lighting Needs!

• Pendants & Linear Pendants Above a Kitchen Island
  Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.

• Pendants & Chandeliers Above a Dining Room Table
  Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table

• Pendants and Chandeliers in Open Areas
  The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.

We appreciate your business and hope you love your new light!

• Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
• Get function and style! Browse our site for coordinating lights and expert lighting advice.

Assembly Instructions

How to Identify the Fixture’s Wires

• Hot: Smooth, Black, or Transparent with Black Inner Thread
• Neutral: Ribbed, White or Transparent with White Inner Thread
• Ground: Copper, Bare Metal, Green, or Transparent Inner Thread

Lightinginstructions.com
Get help, quick tips, and explore curated content

For Customer Service, contact the place of purchase to arrange for replacement parts.

IMPORTANT:

• All installation work should be done by accredited professional.
• Shut off power supply at fuse or circuit breaker!
• Use only the specified bulbs. Do not exceed the maximum wattage!

Assembly Instructions:

PREPARING FOR INSTALLATION

• Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power
  at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. From the parts bag remove the mounting strap (B) assembly. Mounting strap (B) contains several pairs of threaded holes, find the pair of holes that matches the spacing of the holes on the junction box. Two sets of mounting screws (A & D) should be attached to the mounting strap (B). You may need to tighten nuts (C) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. Remove the canopy (F) and tighten nuts (C) onto mounting screws (A) to hold the screws in place. Place mounting strap (B) over the junction box. Secure mounting strap (B) to the junction box with mounting screws (D) and use a screwdriver to tighten the screw firmly. Pull house wires from the center of the mounting strap.

ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.

CONNECTING THE WIRES

Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.

FINISHING THE INSTALLATION

Lift canopy (F) up over mounting strap (B) so that mounting screws (A) protrude from the holes in the canopy (F). Thread deco nuts (G) onto the exposed threads of mounting screws (A) until the canopy (F) is secure and snug against the ceiling.
Install light bulbs (not provided) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage.
Thread rod (I) to post (H) until secure. Lift glass shade (J) up to  canopy (F) until rod (I) protrudes from the hole in the glass shade (J). Secure glass shade (J) in place using washer (K), hex nut (L), cap (M), and finial (N) on the exposed threads of rod (I) in the order shown in the diagram. Tighten until secure. After installing the fixture, apply a clear silicone rubber caulking to seal the gap between the enclosure and the mounting surface. Your installation is complete. Turn on the power and test the fixture.

References

• Lighting Instructions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>