GOLDEN LIGHTING 3164-BA3 Aenon Vanity Light Installation Guide
- May 15, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3164-BA3 Aenon Vanity Light
Product Information
Specifications
- Brand: Golden Lighting
- Model: 3164-BA3 BCB-HWG
- Height: 8′ – 13′
- Width: 30′ – 38′
- Recommended Installation Height: At least 30″ above countertop or table
- Fixture Type: Pendants & Linear Pendants
Product Usage Instructions
-
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop. -
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table. -
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Assembly Instructions
-
No Assembly Required – This item arrives assembled and ready for installation.
-
Place the fixture’s backplate (G) over mounting plate (B).
Align the holes in backplate (G) with the holes found on mounting plate (B). Insert small screws (A) into the holes found on backplate (G) and mounting plate (B). Tighten screws until backplate (G) is secure to mounting plate (B) and the fixture is snug against the wall. -
Attach glass panels (H) and iron plates (I) to the fixture by aligning holes and holding against screws (L) found on the fixture arms until screws protrude out from the holes in the glass panels (H) and iron plates (I) . Secure glass panels (H) and iron plates (I) to fixture arms using deco nuts (J). Thread until secure.
-
Install light bulbs (not included) into sockets (K) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
FAQ
How do I identify the fixture’s wires?
The fixture wires are labeled as Hot, Neutral, and Ground. Match these with
the corresponding house wires labeled as Hot, Neutral, and Ground. The ground
wire is typically copper, bare metal, green, or transparent inner thread.
Where can I get replacement parts or customer service?
Contact the place of purchase for replacement parts or customer service
inquiries.
INSTRUCTION
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
Assembly Instructions
3164-BA3
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- WiresNeutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. PLEASE NOTE: This fixture may be mounted with the sockets and
glass facing up or down. Please decide how you would like the fixture to be
hung and turn the backplate accordingly. 1. Mounting plate (B) contains
several pairs of threaded holes. Find the pair of holes on mounting plate (B)
that matches the spacing of the holes on the junction box. Mounting plate (B)
may be attached to backplate (G). If attached, use a screwdriver to remove
small screws (A). Place small screws (A) aside for later use. 2. Place
mounting plate (B) over the junction box. After you determine the proper
placement, use a pencil to mark the wall through the two circular holes found
on mounting plate (B). 3. Set aside mounting plate (B) for now. Use a drill
bit to create two holes on your pencil marks and insert plastic anchors (D)
into the holes made until the plastic anchors are flush with the wall. Align
mounting plate (B) with the plastic anchors (D). Using a drill or screwdriver,
insert mounting screws (F) into the plastic anchors (D). 4. Secure mounting
plate (B) to the junction box using mounting screws (C) and a screwdriver.
Tighten the screws securely. Pull the house wires through the center of
mounting plate (B).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Place the fixture’s backplate (G) over mounting plate (B). Align the holes in backplate (G) with the holes found on mounting plate (B). Insert small screws (A) into the holes found on backplate (G) and mounting plate (B). Tighten screws until backplate (G) is secure to mounting plate (B) and the fixture is snug against the wall. 7. Attach glass panels (H) and iron plates (I) to the fixture by aligning holes and holding against screws (L) found on the fixture arms until screws protrude out from the holes in the glass panels (H) and iron plates (I). Secure glass panels (H) and iron plates (I) to fixture arms using deco nuts (J). Thread until secure. 8. Install light bulbs (not included) into sockets (K) in accordance with the fixture’s specifications. Do not exceed maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>