ENFORCER MQ SKPR-Bxxx-xQ Bluetooth Access Controllers Installation Guide
- June 3, 2024
- ENFORCER
Table of Contents
ENFORCER MQ SKPR-Bxxx-xQ Bluetooth Access Controllers
Getting Started:
Download the SL Access™ app from the corresponding store for your phone (iOS 11.0 and above, Android 5.0 and above).
Get the complete Installation Manual, SL Access App User Manual, and more at
SECO LARM’s website
NOTES:
a. Be sure to set your smartphone to automatically download app updates so
that you always have the latest version of the app.
b. The app will appear in your device’s default language if available. If the
app does not support your device language, it will default to English.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SECO-LARM is under license. Other trademarks and trade names are those of their respective owners.
Quick Installation:
This manual is for installers looking to do a basic installation and setup of the ENFORCER Bluetooth® keypad/reader (SK-B141-PQ shown, others similar).
Mounting and Installation
See the Additional Information sheet included in your product for basic mounting and installation instructions. For more in-depth installation and advanced programming instructions, see the corresponding product page at www .seco-larm.com and download the Installation Manual and Administrator Guide.
Basic Wiring Diagram
AC-Powered Lock Wiring
AC powered locks should be wired as follows. Their peripherals are wired the same as above.
IMPORTANT NOTES
- To protect the relay, you must install the enclosed diode—with the cathode (striped end ) toward the positive side—for DC powered locks and install the varistor (MOV, ) for AC powered locks and for electromagnetic locks unless your lock has a diode/MOV built in. Failure to use these as directed will void the warranty.
- Use the blue wire for fail-secure applications and the yellow wire for fail-safe applications. Use electrical tape to insulate the end of any unused wire.
See Installation Manual and Administrator Guide online for details.
SL Access Quick Setup
Understanding the SL Access Home Screen
NOTES
a. On opening the app, you may get a message asking you to enable
Bluetooth. Bluetooth must be enabled to use the app and the device must be in
range.
b. You may see the word “Searching…” at the top of the screen (see
below). Bluetooth has a limited range of about 60 feet (20m), but will be much
less in practice. Move closer to the device, but if “Searching…,” continues
toshow you may need to exit and reopen the app.
Log In to the Device
- From a position near the device, click “Login” at the top left of the hemiscreen.
- Type “ADMIN” (case sensitive) in the ID section.
- Type the factory default ADMIN passcode “12345” as the passcode and click “Confirm.
NOTES
a. The administrator’s ID is ADMIN and cannot be changed.
b. The factory default passcode should be changed from the “Settings”
page immediately for better security (see pg. 4)
c. Users will use the same app, and will log in in the same manner The
home and login screens willow the same, however their functionality will be
limited to unlocking the door, choosing “Auto,” and adjusting their “Auto
Proximity Range” for the app’s “Auto” unlock feature.
SL Access Quick Setup (Continued)
Manage Device and Set Device Settings
Four function buttons allow you to:
- Open the user page to add or manage users
- View and download the audit trail
- Back up and restore device settings (also convenient for replicating to another device).
Below the function buttons are device settings:
- Device name – give a descriptive name
- ADMIN passcode – change immediately
- ADMIN proximity card
- Door sensor – required for the door-propped open / door-forced-open alarm)
- Output mode (global) – timed relock, remain unlocked, remain locked, or toggle
- Timed relock output time – 1~1,800 sec
- Number of wrong codes – Number that will trigger a temporary device lockout
- Wrong code lockout time – how long the device will remain locked out
- Tamper alarm – Vibration sensor
- Tamper vibration sensitivity – 3 levels
- Tamper alarm duration – 1~255 min
- Auto proximity range – for ADMIN app “Auto”
- Device time – automatically syncs with ADMIN phone date and time
- Key tone – keypad sounds can be disabled
Manage Users
Add users by pressing the “Add” button top right. Current users will be listed in order of their addition
User Info
Edit users, add card/fob, set access, and override global output mode
Audit Trail
View last 1,000 events, save to phone, share, or email for archive
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022 SECO-LARM U.S.A., Inc. All rights reserved.
SECO-LARM® U.S.A., Inc
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone:949-261-2999 |
800-662-0800
Email:[email protected]
