ENFORCER SD-7104SGEX1Q Vandal Resistant Push Exit Plates Instruction Manual
- May 15, 2024
- ENFORCER
Table of Contents
SD-7104SGEX1Q / SD-7204SGEX1Q
SD-7304SGEX1Q
Vandal Resistant Push-to-Exit Plates
Manual
SD-7104SGEX1Q Vandal Resistant Push Exit Plates
Features:
- Switch contact rating: 50A@24VAC
- Equipped with NO/NC (DPST) switch
- “EXIT” and “SALIDA” silk-screened on plate (except SD-7304SGEX1Q)
- Available with slimline, single-gang, and European plates
- Vandal-resistant 1″ (25mm) pushbutton switch
Installation:
Please read the manual carefully before beginning installation.
- Run two wires through the wall to the back box.
- Connect wires to either 1-2 (N.C.) or 3-4 (N.O.).
- For weather-resistant installation, use a waterproof back box and apply a bead of silicone sealant where the back box contacts the faceplate and around the faceplate mounting screws.
- Screw plate to the back-box, using caution not to pinch any wires.
NOTE: Use only low-voltage, power-limited/Class 2 power supply and low- voltage field wiring not to exceed 98.5ft (30m).
Parts List:
1x Push-to-exit button / faceplate
4x Crimp-style connectors
2x Mounting screws
1x Manual
Specifications:
| Model | SD-7104SGEX1Q | SD-7204SGEX1Q | SD-7304SGEX1Q |
|---|---|---|---|
| Plate | Slimline | Single-gang | European |
| Contact rating | 50A@24VAC | ||
| Switch type | NO/NC | ||
| Destructive attack level | Level I | ||
| Line security | Level I | ||
| Endurance level | Level I | ||
| Standby power | Level I | ||
| IP Rating | IP65 | ||
| Operating temperature | -40-140° F (-20°-60° C) | ||
| Dimensions | 41/2″x19/16″x13/16″ (115x39x20 mm) | 41/2″x23/4″x213/16″ (115x70x20 | |
| mm) | 33/8″x33/8″x13/16″ (86x86x20 mm) |
Dimensions:
Connections:
Sample Installations:
- Installation with an Electromagnetic Lock
NOTE: Use only low-voltage, power-limited/Class 2 power supply and low-voltage field wiring not to exceed 98.5ft (30m). - Installation with an Electromagnetic Lock and Keypad
NOTE: Use only low-voltage, power-limited/Class 2 power supply and low-voltage field wiring not to exceed 98.5ft (30m). - Installation with an Electric Door Strike
NOTE: Use only low-voltage, power-limited/Class 2 power supply and low-voltage field wiring not to exceed 98.5ft (30m).
California Proposition 65 Warning: These products may contain chemicals
which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
IMPORTANT WARNING: For a weather-resistant installation, ensure that the
unit is installed in a waterproof back box, and that the faceplate and
faceplate screws are properly sealed. Incorrect mounting may lead to exposure
to rain or moisture in the enclosure which could cause a dangerous electric
shock, damage the device, and void the warranty. Users and installers are
responsible for ensuring that this product is properly installed and sealed.
IMPORTANT: Users and installers of this product are responsible for
ensuring that the installation and configuration of this product complies with
all national, state, and local laws and codes related to locking and egress
devices. SECO-LARM will not be held responsible for the use of this product in
violation of any current laws or codes.
WARRANTY: This SECO-LARM product is warranted against defects in material
and workmanship while used in normal service for one (1) year from the date of
sale to the original customer. SECO-LARM’s obligation is limited to the repair
or replacement of any defective part if the unit is returned, transportation
prepaid, to SECO-LARM. This Warranty is void if damage is caused by or
attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair or alteration, improper or abnormal usage, or faulty installation, or
if for any other reason SECO-LARM determines that such equipment is not
operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive
remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral,
incidental, or consequential personal or property damage of any kind to the
purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and
improvement. For that reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for
misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their
respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights
reserved.
SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: 949-261-2999 |
800-662-0800
Website: www.seco-larm.com
Email: [email protected]
PITSW1
Order Part# 763-158-6%
MI_SD-7x04SGEX1Q_220909.docx
SECO-LARM U.S.A., Inc.