ENFORCER N6506-3W4Q IP Covert PIR Camera Instruction Manual

ENFORCER N6506-3W4Q IP Covert PIR Camera

Product Information

Specifications

• Model: EV-N6506-3W4Q
• Resolution: 1440p
• Image Sensor: 1/2.8 5MP Sony CMOS
• Lens: 3.7mm Covert pinhole lens
• Video Compression: H.265/MJPEG
• Wide Dynamic Range: D-WDR
• Day & Night Function: True Day & Night with ICR module
• Power: 12VDC, 802.3af PoE
• Network Protocol: ONVIF Profile S
• Noise Reduction: 2DNR, 3DNR

FAQ

• How do I access the IP Camera interface?
• To access the interface, input the IP address into the browser’s address bar, install VideoPlayTool if needed, enter the default credentials, and click Login.
• How can I adjust the colour settings on the camera?
• You can adjust colour settings by clicking on the Color panel button and making adjustments in the Image Settings panel.

Program Features

• Exposure – Adjust the shutter speed, automatic gain control (AGC), and defog settings.
• Digital Wide Dynamic Range (D-WDR) – Provide clear images even under circumstances where backlight illumination can vary.
• Back Light Compensation (BLC) – Adjust the exposure to properly display the subject in front of bright light sources.
• White Balance – Adjust the colour temperature/image colour.
• Day & Night – Adjust the level of ambient light that triggers the camera to switch between color and B/W modes.
• Digital Noise Reduction – (DNR) Adjust for less interference on the screen in an area with low illumination.

Accessing the IP Camera Interface

Login Screen

1. To access the IP Camera interface, input the IP address of the front-end device into the URL address bar of the Microsoft Edge browser (default IP address: 192.168.1.10).

2. VideoPlayTool installation is required when the
   IP camera interface is first accessed. Follow the prompts to install VideoPlayTool.

3. Refresh the page.

4. In the following login screen, input the default Username (Default: admin) and Password (Default: Leave Blank).

5. Click “Login” to proceed.

IP Camera Interface
Once within the IP Camera interface, the following tabs are made available:

• Live – The Live tab provides the primary live camera feed and limited settings for adjusting the camera’s image.
• Playback –The playback settings allow for full replay and review of the recorded video.
• Alarm – Display all alarm notifications
• Remote Setting – The Remote Setting tab allows for full configuration of the IP camera’s settings.
• Local Setting – The Local Setting tab allows for search and review of programmed alarms.
• Log Out – Press the Log out tab to log out completely of the IP camera interface.

Color Settings

To open the Color panel, click the button. The Image Settings panel allows for adjustment of the video image’s brightness, contrast, hue, and saturation.

• Brightness – Adjust the brightness of the video image.
• Contrast – Adjust the contrast of the video image.
• Saturation – Adjust the saturation of the video image.
• Hue – Adjust the Hue of the video image.

Playback Settings
The playback settings allow for full replay and review of recorded video.

• PlayBack – Choose between Remote or Local playback.
• Query Mode – Select to search for video by Name or by specific Time.
• Type – Select the type of video or picture to search for.
• Start Time – Select the beginning video recording time to search.
• End Time – Select the ending video recording time to search.
• Stream – Mainstream only.
• Channel – Channel 1 only.

Alarm

Alarm Type
The alarm log records the camera’s alarm features. Displaying the alarm type, date, time, device, and channel. Use the checkboxes to select the alarm type to be displayed.

Operation

• Prompt – Check the display operation log.

Remote Setting – Alarm

• Intelligent Alert – Configure alerts.
• Video Blind – Configure settings pertaining to camera being blinded (spray painted or covered).
• Vehicle Detection – Configure vehicle detection.
• Video Loss – Configure settings for loss of video.
• Abnormal – Configure settings for abnormalities (IP conflicts, NetAbort).

Remote Setting – Alarm – Intelligent Alert

• Enable – Toggle to enable.
• Human Detect – Check to detect humans only.
• Sensitivity – Select the sensitivity from Lowest to Highest (default = middle).
• Rule – Select the area to monitor.
• Period – Set the schedule to monitor.
• MD Intervals – Set the desired intervals in seconds (default = 2 seconds).
• Snapshot Channel – Default = 1.
• PTZ Activation – Not supported.
• Send Email – Check to send an alert using email.
• FTP Upload – Check to send an alert to a FTP server.
• Mobile reported – Not supported.
• Write log – Check to write to the log file.
• Alarm Sound – Check to enable sound.
• Alarm Interval – Set the Alarm Interval in seconds (default = 0).
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – Alarm – Video Blind

• Enable – Toggle to enable.
• Sensitivity – Select the sensitivity from Lowest to Highest (default = Middle).
• Period – Set the schedule to monitor.
• Snapshot channel – Default = 1.
• PTZ activation – Not supported.
• Send email – Check to send an alert using email.
• FTP upload – Check to send alert to a FTP server.
• Mobile reported – Not supported.
• Write log – Check to write to the log file.
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – Alarm – Vehicle Detection

• Channel – Select channel to use (default = CH01).
• Enable – Toggle to enable.
• Period – Set the schedule to monitor.
• Tour – Default = 1.
• PTZ Activation – Not supported.
• Send Email – Check to send an alert using email.
• Mobile reported – Not supported.
• Write log – Check to write to the log.
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – Alarm – Video Loss

• Enable – Check to enable.
• Period – Set the schedule to monitor.
• Snapshot Channel – Default = 1.
• PTZ Activation – Not supported.
• Send Email – Check to send alert using email.
• FTP upload – Check to send alert to a FTP server.
• Mobile reported – Not supported.
• Write log – Check to write to the log file.
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – Alarm – Abnormal

• Event Type:
  • IP Conflict – Will alert when another device has the same IP as camera.
  • NetAbort – Will alert when camera is disconnected from the network.
• Enable – Toggle to enable.
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – System

• General – General configurations.
• Encode – Encoding configurations.
• Network – Network configurations.
• NetService – Services available.
• Display – OSD configurations.
• PTZ Config – PTZ configurations.
• RS232 – Serial port configurations.
• Camera param. – Advanced camera configurations.
• Color param. – Advanced color configurations.

Remote Setting – System – General

• Time Zone – Select time zone.
• System Time – Enter date and time.
• Date Format – Select the format to display the date.
• DST – Check for Daylight Savings Time.
• Date Separator – Select character to use to separate the date.
• Time Format – Select between 12-hour or 24-hour clock.
• Language – Select language.
• HDD Full – Select to either overwrite (default) or stop recording when a hard drive is full.
• Dev No – Set the number for the DVR (default = 0).
• Video Standard – Select between PAL or NTSC.
• Auto Logout – Set a time limit in minutes to automatically log off (default = 0).
• MachineName – Set MachineName (default = LocalHost).
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – System – Encode
Set encoding parameters for both Main stream and Sub stream.

• Compression – Select between H.265 or H.265X.
• Resolution – Select between 2MP, 4MP, or 5MP.
• Frame Rate (fps) – Select the frames per second.
• Bit Rate Type – Select between VBR or CBR.
• Quality – Select between Worst and Best (default is good).
• Bit Rate (Kb/S) – Set the Bit rate.
• I Frame Interval – Set the I frame interval (default = 2).
• Video/Audio – Check to record video or audio.
• Static Encode Config – Select profile between Baseline, Main Profile, and High profile. High profile takes up more space for the stream, but the picture quality is better.
• Smart Encode – Select to use smart encoding on H.265+.
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – System – Network

• Net Card – Select network adapter.
• DHCP Enable – Check to enable DHCP (default = enable).
• Adaptive IP – Check to enable Adaptive IP (default = enable).
• IP Address – Enter IP Address for the camera (default IP is assigned by DHCP).
• Subnet Mask – Enter the subnet mask.
• Gateway – Enter default gateway.
• Primary DNS – Enter the primary DNS server address.
• Secondary DNS – Enter the secondary DNS server address.
• Media Port – Enter TCP steaming port (default = 34567).
• HTTP Port – Enter HTTP port (default = 80).
• Onvif Port – Enter Onvif port (default = 8899).
• MAC Address – Displays camera mac address.
• Onvif Check – Check to enable Onvif Check.
• HS download – Check to enable High Speed download.
• Refresh – Reload current page.
• Save – Click save.

Transfer Policy

• Adaptive – For lower bandwidth network. Preview screen automatically adjusts to sub stream.
• Quality Preferred – For higher bandwidth network. Preview screen stays in mainstream.
• Fluency Preferred – Changes the encoder settings and lowers the stream without reducing frame rate to ensure a smoother video.
• Network Priority – Limits the users that can view the camera simultaneously. Users with higher bandwidth will take priority.

Remote Setting – System – NetService
NetService displays the network services available. Double click each option listed below to configure:

• IP Filter – Blacklist and Whitelist services.
• DDNS – Configure dynamic DNS.
• EMAIL – Use email to send alerts or other services.
• NTP – Set the time server.
• UPNP – Allows devices in your network to discover each other.
• FTP – Configure the file server.
• AlarmServer – Configure an alarm server.
• RTSP – Real Time Streaming Protocol – used to stream camera video over network.
• Cloud – Set up a third-party cloud provider.
• Mobile reported – Not supported.
• Serial pass-through – Configure RS232 settings.
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – System – Display

• CAM Name – Click Setting and Enter camera name.
• Channel – Select channel to use (default = 1).
• Region Cover – Check to enable region cover.
• Time Title – Check the display time on screen.
• Channel Title – Check to display channel on screen.
• Setting – Configure the position of the user interface.
• Refresh – Reload current page.
• Save – Click save.

NOTE: Setting: System – PTZ Config: Not Supported.

Remote Setting – System – RS232

• Function – Select between NONE, Transparent, GPS, and InteractCmd function.
• Baud rate – Set baud rate (max 115200) (default = 115200).
• Data Bits – Set data bits (5 – 8) (default = 8).
• Stop Bits – Set stop bits (1 – 2) (default = 1).
• Parity – Set parity (None, Odd, Even, Mark, Space) (default = None).
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – System – Camera param

• Exposure mode – Set the exposure time. Can choose between Automatic (default) and Manual.
• Day/Night mode (default = blank):
  • Smart Alert – Enable smart alert.
  • Intelligent Variable – Enable Intelligent Variable.
  • Intelligent Infrared – Enable Intelligent Infrared.

• Profiles – Set the white balance for Indoor, Outdoor, Automatic (default = Automatic).
• Image Style – Choose between Style 1, Style 2, and Style 3 (default = Style 2).
• AE Reference – Set the AE reference (default = 50).
• BLC – Turn backlight compensation Open (On) or Close (Off) (default = Close).
• Automatic Gain – Turn automatic gain control Open (On) or Close (Off) (default = Open).
• Slow Shutter – Set the shutter speed No, Weak, In, Strong (default = Weak).
• DayNTLevel – Set Day time NT Level (0~5, default = 3).
• DWDR – Turn digital wide dynamic range Open (On) or Close (Off) (default = Close).
• Defogging – Turn defogging Open (On) or Close (Off) (default = Close).
• Front end command – Send a communication to front end.
  • Send
  • Save
• Mirror – Check to mirror image.
• Flip – Check to flip image.
• Anti-Flicker – Check to enable Anti-Flicker.
• IRSwap – Check to enable IRSwap.
• Prevent Exposure – Check to reduce red face exposure.
• Minimum time – Set the Minimum time in seconds (default = 0.256).
• Maximum time – Set the Maximum time in seconds (default = 65.536).
• Dnc Threshold – Set the Dnc Threshold (default = 3).
• Auto Iris – Choose between Close (Off) and Open (On) (default = Close).
• AE Sensitivity – Adjust sensitivity (default = 5).
• Upper limit – Set the upper limit for D-WDR (default = 50, max = 100).
• IR_Cut – Set the IR Cut to light board switching or automatic switching.
• NightNTLevel – Set NightNTLevel (0~5, Default = 3).
• Refresh – Reload current page.
• Save – Click save.

• Channel – Select channel to use (default = CH01).
• Brightness – Adjust the brightness of the video image.
• Contrast – Adjust the contrast of the video image.
• Saturation – Adjust the saturation of the video image.
• Hue – Adjust the Hue of the video image.
• Mirror – Check to mirror the image.
• Flip – Check to flip the image.
• Restore – Restore default settings.
• Refresh – Reload current page.
• OK – Click OK to save.

Remote Setting – Advanced

• Account – Manage account settings.
• AutoMaintain – Manage automatic reboot and automatic delete settings.
• Default – Restore factory defaults.
• Import Export – Manage import and export config files.
• Reboot – Reboots the camera.
• Upgrade – Manage upgrade on firmware.

Remote Setting – Advanced – Account

• Refresh – Refresh list.
• Add User – Add user.
• Modify User – Set the permission for the user.
• Delete User – Delete user.
• Modify PW – Change password.
• Add Group – Add user group.
• Modify Group – Set the permissions for the user group.
• Delete Group – Delete user group.
• Security – Configure secret questions in case password is forgotten.

Remote Setting – Advanced – AutoMaintain

• Auto-Reboot System – Select a day and time to auto reboot.
• Auto-Delete Old Files – Select the number of days old a file needs to be in order to auto-delete.
• Online Upgrade – Check to automatically check for upgrade.
• Refresh – Reload current page.
• Save – Click save.

Remote Setting – Advanced – Default

• Select the settings to default back to factory settings.
• Click Save to save.

Remote Setting – Advanced – Import Export

• Config Import – Click to import config file.
• Config Export – Click to export config file.
• Log Export – Click to export log file.

Remote Setting – Advanced – Reboot

• Click “Reboot” to reboot the camera.

Remote Setting – Advanced Upgrade

• Browse – Select firmware update file.
• Send – Click Send to start the upgrade process.

Remote Setting – Info

• Log – View Log file.
• Version – View software version.
• QR Code – Not supported.

Remote Setting – Info – Log

• Type – Select the type of log file to search (All, System, Config, Storage, Alarm Event, Weekday, Account, or Playback).
• Start Time – Select start time for search.
• End Time – Select end time for search.
• Search – Fill in the start and end time and click search to display log.

Setting – Info – Version

• Display all the device information.

Troubleshooting

FCC STATEMENT

FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
California Proposition 65 Warning: These products may contain chemicals that are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved.

CONTACT

SECO-LARM ® U.S.A., Inc.

• 16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
• Phone: 949-261-2999 | 800-662-0800 Email: sales@seco-larm.com

References

• La Armería de Madrid - fabricantes de armas y rifles
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>